2-6
PCS 103 337
17
TUNER
Storing Preset Stations
You can store up to 40 radio stations in
the memory. When a preset radio
station is selected, the preset number
appears next to the frequency on the
display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROGRAM for more than
one second.
™ The PROG flag starts flashing and
“AUTO” will be displayed.
™ The system will search for every
available station in the FM
waveband first, then search the
AM waveband.
™ All available stations will be stored
automatically. The frequency and
preset number will be displayed
briefly.
™ The system will stop searching
when all the available radio
stations are stored or when the
memory for 40 preset radio
stations is used.
™ The system will remain tuned to
the last stored preset radio
station.
Notes:
–You can cancel the automatic
programming by pressing PROGRAM or
Ç
(on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10
before starting automatic programming,
only the preset numbers 10 to 40 will
be programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press PROGRAM for less than one
second.
™ The PROG flag starts flashing.
™ The next available preset number
will be displayed for selection.
4 Press à or á to tune to the
desired frequency.
• If you wish to store the radio station
to another preset number, press 4
or 3 to select the desired preset
number.
5 Press PROGRAM again.
™ The PROG flag disappears and
the radio station will be stored.
• Repeat steps 3 – 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show
"PROGRAM FULL”. If you want to
change an existing preset number,
repeat steps 3 – 5.
–You can cancel manual programming
by pressing
Ç
(on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
Tuning to Preset Radio
Stations
•Press 4 or 3 to select the desired
preset number.
™ The preset number, radio
frequency, and waveband appear
on the display.
18
TAPE
SOUND NAVIGATION - JOG
STANDBY
-
ON
PROGRAM CLOCK•TIMER DIM
FULL AUTO STOP
MASTER
VOLUME
TAPE 2
TAPE 1
PLAY
STOP
.
O
PEN
PAU
SE
▲
RECORD
P
LAY
STOP
.
OPE
N PAU
S
E
▲
▲
▲
▲
FW-
C10
MINI HIFI SYSTEM
CD1 • 2 • 3 FM •AM
TAPE 1 • 2
TAPECD TUNER
AUX
PRESET
▲
▲
TUNING
▲
▲
▲
▲
STOP• CLEAR
SEARCH
PLAY• PAUSE PREV NEXT
D
B
B
VIDEO
▲
▲
▲
▲
▲
▲
OPTIMAL
JAZZ
ROCK
TECHNO
JOG
CONTROL
Loading a tape
1 Press STOP•OPEN.
2 The tape deck door opens.
3 Load the tape with the open side
downward and the full spool to the
left.
4 Close the tape deck door.
Tape Playback
1 Press TAPE to select TAPE mode.
™ "TAPE" will be displayed.
2 Load the tape into the selected tape
deck.
3 Press PLAYÉ to start playback.
•To interrupt playback, press PAUSE.
•To resume playback, press PA USE
again.
4 Press STOP•OPEN to end
playback.
Rewind/Fast Forward
When playback is stopped
1 You can rewind or fast forward a
tape by pressing à or á ,
respectively.
™ The tape will stop automatically at
the end of rewinding or fast
forwarding.
2 Press STOP•OPEN to stop
rewinding or fast forwarding.
Continuous Playback From
Ta pe Deck 2 to Tape Deck 1
1 Press TAPE to select TAPE mode.
2 Load the tapes in tape decks 1 and 2.
3 Press PLAY 2 on tape deck 2.
4 Press PAUSE on tape deck 1.
5 Press PLAY 2 on tape deck 1.
™ Playback will begin with tape deck
2 and will continue with tape deck
1 when playback on tape deck 2
ends.
6 Press STOP•OPEN if you want to
stop playback before the end of the
tape in tape deck 1 or tape deck 2.
Notes:
–During rewinding or fast forwarding of a
tape, it is also possible to listen to
another source (e.g. CD, TUNER or
AUX).
To Next Page
Loading...
