PCS 103 339
2-8
21
RECORDING CLOCK
• Recording will start automatically.
5 Press STOP•OPEN on tape deck 1
and tape deck 2 to stop dubbing.
Notes:
–At the end of side A, flip the tapes to
side B and repeat the procedure.
– Dubbing of tapes is only possible from
tape deck 2 to tape deck 1.
–To ensure good dubbing, use tapes of
the same length.
Recording from other
sources
(only on tape deck 1)
1 Load a blank tape into tape deck 1.
2 Press CD, TUNER or AUX.
•Start playback of the selected source.
3 Press RECORD on tape deck 1 to
start recording.
™ The
REC starts flashing.
4 Press PAUSE to interrupt
recording.
5 Press STOP•OPEN on tape deck 1
to stop recording.
Note:
– During recording, it is not possible to
listen to another sound source.
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER,
etc.). The clock will be displayed for
about seven seconds.
•Press CLOCK•TIMER briefly.
™ “10:38
PM or 22:38” (the
current time in either 12- or 24-
hour mode) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
™ “--:--” will be displayed if the
clock is not set.
Clock Setting
The clock can be set in either 12- or
24-hour mode, e.g. “12:00
AM“ or
“00:00“. Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK•TIMER to select
clock mode.
2 Press PROGRAM to select 12- and
24- hour mode.
™ If 12-hour mode is selected,
“12:00“ starts flashing and the
AM lights up.
™ If 24-hour mode is selected,
“00:00” starts flashing.
3 Set the hour with à or á on the
system.
4 Set the minute with í or ë on
the system.
SOUND NAVIGATION - JOG
STANDBY
-
ON
PROGRAM CLOCK•TIMER DIM
MASTER
VOLUME
FW-
C10
MINI HIFI SYSTEM
CD1 • 2 • 3 FM •AM
TAPE 1 • 2
TAPECD TUNER
AUX
PRESET
▲
▲
TUNING
▲
▲
▲
▲
STOP• CLEAR
SEARCH
PLAY• PAUSE PREV NEXT
D
B
B
VIDEO
OPTIMAL
JAZZ
ROCK
TECHNO
JOG
CONTROL
22
TIMER SLEEP TIMER
5 Press CLOCK•TIMER again to
store the setting.
™ The clock starts.
•To exit without storing the setting,
press Çon the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
Timer Setting
• The system can switch on to CD or
TUNER mode automatically at a
preset time. It can ser ve as an alarm
to wake you up.
• Before setting the timer, make sure
the clock is set correctly.
• The timer will always be switched on
once it is set.
• The volume of the timer will
increase from the minimum
level until the volume level
before the set is switched to
standby mode.
1 Press and hold CLOCK•TIMER
for more than two seconds to
select timer mode.
™ “12:00
AM
” or “00:00" or the
last timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
™ The
TIMER
starts flashing.
™ The selected source is lit while
other available sources are
flashing.
2 Press CD or TUNER to select the
desired source.
• Before selecting CD, make sure a CD
is loaded in the CD carousel tray.
3 Press à or á on the system to set
the hour for the timer to start on
the system.
4 Press í or ë on the system to set
the minute for the timer to start.
5 Press CLOCK•TIMER to store
the start time.
™ The timer is now set.
™ The
TIMER
remains on the display.
•At the preset time, the timer will be
activated.
™ The selected source will be
played.
Notes:
– During timer setting, if no button is
pressed within 90 seconds, the system
will exit timer setting mode
automatically.
– If the source selected is TUNER, the
last tuned frequency will be switched
on.
– If the source selected is CD, playback
will begin with the first track of the
selected disc or program. If the CD
trays are empty, the TUNER will be
selected instead.
–The timer will not activate if a recording
is in progress.
To s w itch off the TIMER
1 Press and hold CLOCK•TIMER
for more than two seconds.
2 Press Ç on the system to cancel the
timer.
™ The timer is now switched off.
™ The display will show "CANCEL"
and the
TIMER
disappears.
To start the TIMER again (for the
same preset time and source)
1 Press and hold CLOCK•TIMER
for more than two seconds.
2 Press CLOCK•TIMER again to
store the start time.
™ The timer is now on.
™ The
TIMER
appears on the display.
Sleep Timer
(only on remote
control)
This feature allows you to select a
length of time after which the system
will switch to the standby mode
automatically.
1 Press SLEEP on the remote control
repeatedly to select a period of time.
™ The selections are as follows (time
in minutes):
60
™™
™™
™ 45
™™
™™
™ 30
™™
™™
™ 15
™™
™™
™ OFF
™™
™™
™
60 …
™ “SLEEP XX” or “OFF” will be
displayed. "XX" is the time in
minutes.
2 When you reach the desired length
of time, stop pressing the SLEEP
button.
™ After this amount of time passes,
the system will switch to the
standby mode.
To switch off the Sleep Timer
•Press SLEEP repeatedly until "OFF"
is displayed, or press the
STANDBY ON button.
To Next Page
Loading...
