3139 115 20462 (ENG)
19
TUNER
CD1 • 2 • 3 FM • AM
TAPE 1 • 2
MINI HIFI SYSTEM
VIDEO/ CDR
STOP• CLEAR
SEARCH•TUNING
RECORD
PLAY• PAUSE PREV NEXT
PRESET
CLOCK•TIMER DUBBING A. REPLAY PROGRAM
▲
▲
SOUND NAVIGATION - JOG
VOLUME
DISC 1
DISC 2
DISC 3
CD TUNER TAP E AUX
D
B
B
V
E
C
D
S
C
I
N
C
R
E
D
I
B
L
E
S
U
R
R
O
U
N
D
FM
DIM MODE
DEMO STOP
STANDBY-ON
Note:
– For 'PLUG & PLAY' feature, please refer
to page 12.
Tuning to radio stations
1 Press TUNER (FM•AM) to select
TUNER mode.
➜ “TUNER” will be displayed.
A few seconds later, the current radio
frequency will be displayed.
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press à or á for more than one
second, then release.
➜ The display will show “SEARCH”
until a radio station with sufficient
signal strength is found.
¶ Repeat this procedure until the
desired station is reached.
¶ To tune to a weak station, briefly
press à or á repeatedly until the
display shows the desired frequency
and/or when the best reception has
been obtained.
Storing Preset Stations
You can store up to 40 radio stations in
the memory. When a preset radio
station is selected, the preset number
appears next to the frequency on the
display.
Automatic programming
1 Press TUNER (FM•AM).
2 Press PROGRAM for more than
one second.
➜ The PROG flag starts flashing and
“AUTO” will be displayed.
➜ The system will search for every
available station in the FM
waveband first, then search the
AM waveband.
➜ All available stations will be stored
automatically. The frequency and
preset number will be displayed
briefly.
➜ The system will stop searching
when all the available radio
stations are stored or when the
memory for 40 preset radio
stations is used.
➜ The system will remain tuned to
the last stored preset radio
station.
Notes:
– You can cancel the automatic
programming by pressing PROGRAM or
Ç
(on the system only).
– If you want to reserve a section of
preset numbers, for example preset
numbers 1 to 9, select preset 10
before starting automatic programming,
only the preset numbers 10 to 40 will
be programmed.
Manual programming
1 Press TUNER (FM•AM).
2 Press TUNER (FM•AM) again to
select the desired waveband : FM or
AM.
3 Press PROGRAM for less than one
second.
➜ The PROG flag starts flashing.
➜ The next available preset number
will be displayed for selection.
4 Press à or á to tune to the
desired frequency.
¶ If you wish to store the radio station
to another preset number, press 4
or 3 to select the desired preset
number.
5 Press PROGRAM again.
➜ The PROG flag disappears and
the radio station will be stored.
¶ Repeat steps 3 – 5 to store other
preset radio stations.
Notes:
– When 40 radio stations are stored and
you attempt to store another radio
station, the display will show "FULL”. If
you want to change an existing preset
number, repeat steps 3 – 5.
– You can cancel manual programming
by pressing
Ç
(on the system only).
– During programming, if no button is
pressed within 20 seconds, the system
will exit program mode automatically.
pg 01-30/C380/37-En 12/6/00, 2:21 PM19
To Next Page
Loading...
