Philips FW-C380 - SERVICE TEST PROGRAM; Table 2; TEST Activated with ACTION

3139 115 20462 (ENG)
24
CLOCK TIMER
View Clock
You can view the clock (if it is set) if the
system is in Standby mode or when any
sound source is selected (CD, TUNER,
etc.). The clock will be displayed for
about seven seconds.
¶ Press CLOCK•TIMER briefly (on
the system only).
➜ “PM10:38 or 22:38” (the
current time) will be displayed
depending on whether you have
selected 12- or 24-hour mode.
➜ “--:--” will be displayed if the
clock is not set.
Clock Setting
The clock can be set in either 12- or
24-hour mode, e.g. “AM12:00“ or
“00:00“. Before setting the clock, you
must be in the View Clock mode.
1 Press CLOCK•TIMER to select
clock mode.
2 Press PROGRAM to select 12- and
24- hour mode.
➜ If 12-hour mode is selected,
“AM12:00“ starts flashing.
➜ If 24-hour mode is selected,
“00:00” starts flashing.
3 Set the hour with à or á on the
system.
4 Set the minute with í or ëon the
system.
CD1 • 2 • 3 FM • AM
TAPE 1 • 2
MINI HIFI SYSTEM
VIDEO/ CDR
STOP• CLEAR
SEARCH•TUNING
RECORD
PLAY• PAUSE PREV NEXT
PRESET
CLOCK•TIMER DUBBING A. REPLAY PROGRAM
▲
▲
SOUND NAVIGATION - JOG
VOLUME
DISC 1
DISC 2
DISC 3
CD TUNER TAPE AUX
D
B
B
V
E
C
D
S
C
I
N
C
R
E
D
I
B
L
E
S
U
R
R
O
U
N
D
DIM MODE
DEMO STOP
STANDBY-ON
5 Press CLOCK•TIMER again to
store the setting.
➜ The clock star ts.
¶ To exit without storing the setting,
press Çon the system.
Notes:
– During clock setting, if no button is
pressed within 90 seconds, the system
will exit clock setting mode
automatically.
– When a power interruption occurs, the
clock setting is erased.
Timer Setting
¶ The system can switch on to CD ,
TUNER or TAPE mode automatically
at a preset time. It can serve as an
alarm to wake you up.
¶ Before setting the timer, make sure
the clock is set correctly.
¶ The timer will always be switched on
once it is set.
¶ The volume of the timer will
increase from the minimum
level to the most recently
selected volume level.
1 Press and hold CLOCK•TIMER
for more than two seconds to
select timer mode.
➜ “AM12:00” or “00:00" or the last
timer setting starts flashing
depending on whether you have
selected 12- or 24-hour mode.
➜ The TIMER starts flashing.
➜ The selected source is lit while
other available sources are
flashing.
2 Press CD , TUNER or TAPE to
select the desired source.
¶ Before selecting CD or TAPE, make
sure a disc or tape is loaded in the
CD tray or tape deck 2.
3 Press à or á on the system to set
the hour for the timer to start.
4 Press í or ë on the system to set
the minute for the timer to start.
5 Press CLOCK•TIMER to store
the start time.
➜ The timer is now set.
➜ The TIMER remains on the display.
¶ At the preset time, the timer will be
activated.
➜ The selected source will be
played.
pg 01-30/C380/37-En 12/6/00, 2:21 PM24
All manuals and user guides at all-guides.com