Pioneer A-P710 Operating Instructions

A-P710 /A-P510*
SP-P'710
Y) PIONEER’
The Art of Entertainment
STEREO AMPLIFIER
AMPLIFICATEUR STEREO
SOUND FIELD PROCESSOR
PROCESSEUR DE CHAMP SONORE
GR-P510*
SOUND IMAGE CONTROLLER
CONTROLE DE RELIEF SONORE
Operating Instructions
Mode d’emploi
*
F=-P'710"/ F=-P'’71I0OL.
FM/AM DIGITAL SYNTHESIZER TUNER
SYNTONISEUR SYNTHETISEUR A AFFICHAGE NUMERIQUE FM/AM
CT-P7IOWR*
STEREO DOUBLE CASSETTE DECK
DOUBLE PLATINE CASSETTE STEREO
S-P710(V)/S-P510(v)*
.
SPEAKER SYSTEM
SYSTEME D’ENCEINTES
Models for use outside Europe include a
“V/"" in the model name.
Le nom des modéles destinés a
l’extérieur de l’Europe comprend un “’V"’
Models marked with an asterisk (*) are designed for sale in the U.S.A. and Canada.
Les modéles avec cette marque (*) sont concus pour étre vendus aux Etats Unis et au Canada.
[For Canadian model]
CAUTION:10 prEvENT ELECTRIC SHOCK DO
NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION
CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE
BLADES CAN BE FULLY INSERTED TO PREVENT BLADE
EXPOSURE.
ATTENTION:pour prEvENIR LES CHOCS
ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE
AVEC UN PROLONGATEUR UNE PRISE DE COURANT OU
UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES
PEUVENT ETRE INSEREES A FOND SANS EN LAISSER
AUCUNE PARTIE A DECOUVERT.
FM/AM CHANNEL STEP SWITCH
This switch is not provided on models for Europe or
U.K. Adjustment is only necessary when there is a
CHANNEL STEP switch at the rear panel.
The CHANNEL STEP switch is located on the rear
panel of the stereo CD cassette deck receiver. Before
the tuner leaves the factory, this switch is set to the
channel step standard of the areas where the tuner
is sold.
Depending on the position of this switch, each time
TUNING switch is pressed, the frequency display
changes by the following amount:
[100 kHz/10 kHz] position ;
For areas with channel step of 100 kHz for FM and
10 kHz for AM.
[50 kHz/9 kHz] position
For areas with channel step of 50 kHz for FM and 9
kHz for AM.
NOTE:
@ /f the switch is set to the wrong position, correct
turning may not be possible.
Consult your dealer of you are not sure about the ©
radio channei step standard in your area.-
IMPORTANT NOTICE
[For U.S. and Canadian models]
The serial number for this equipment is located on the rear
panel. Please write this serial number on your enclosed war-
ranty card and keep it in a secure area. This is for your
security.
%
WARNING :70 prevent FIRE OR SHOCK HAz-
ARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
LINE VOLTAGE SELECTOR SWITCH
Only multi-voltage models are provided with this switch.
U.S., Canadian, European, U.K., and Australian models
are not provided with this switch.
Mains voltages in Saudi Arabia are 127V and 220V only.
Never use this model with a 110V setting in Saudi Arabia.
Before your model is shipped from the factory, this switch
is set to the power requirements of the destination;
nevertheless, you should check that it is set properly be-
fore plugging the power cord into the wall outlet.
1. Disconnect the power cord.
2. Use a medium-size screwdriver.
3. Insert the screwdriver into the groove on the voltage
selector and adjust so that the tip of the arrow points
to the voltage value of your area.
VOLTAGE SELECTOR
110V

Pioneer A-P710 Specifications

General

Power Output	65 watts per channel into 8Ω (stereo)
Frequency Response	5 Hz to 100 kHz
Signal-to-Noise Ratio	86dB (MM), 108dB (line)
Input sensitivity	0.2mV (MC), 2.5mV (MM), 150mV (line)
Dimensions	420 x 125 x 362mm
Weight	9.7kg
Total harmonic distortion	0.007%
Speaker load impedance	4Ω to 16Ω