Pioneer SC-LX501 - Page 48

12
> Specifications > Settings > Listening Modes > Playback Function > Basic Manual
Troubleshooting | Appendix
■ Channel Level
Setting Item Default Value Setting Details
Front Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Center 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Front Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Height Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
The setting cannot be changed if "Zone 2" is set
in "System Setup" - "Speaker" - "Configuration"
- "Zone Speaker" and Zone 2 is on.
Height Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
•
The setting cannot be changed if "Zone 2" is set
in "System Setup" - "Speaker" - "Configuration"
- "Zone Speaker" and Zone 2 is on.
Surround Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Surr Back Right 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Setting Item Default Value Setting Details
Surr Back Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Surround Left 0.0 dB Select a value between "−12.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
Subwoofer 0.0 dB Select a value between "−15.0 dB" and "＋12.0
dB" (in 0.5 dB increments). A test tone will be
output each time you change the value. Select the
desired level.
■ Dolby Enabled Speaker
Setting Item Default Value Setting Details
Dolby Enabled
Speaker to
Ceiling
6.0ft/1.80m Set the distance between the Dolby Enabled
Speaker and the ceiling. Select between
"0.1ft/0.03m" to "15.0ft/4.50m" (0.1ft/0.03m units).
•
The unit of distance (ft/m) shown is the unit
selected for use in "Distance".
Reflex Optimizer Off You can enhance the reflection effect of Dolby
Enabled Speakers from the ceiling.
"Off": Do not use this function
"On": Use this function
•
The function is not effective if the listening mode
is Pure Direct.