EasyManua.ls Logo

Pit Boss 4 Series - User Manual

Pit Boss 4 Series
59 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
11019
..
300522
READ ALL INSTRUCTIONS
BEFORE INSTALLING AND
USING THE APPLIANCE,
SAVE THESE INSTRUCTIONS.
LISEZ TOUTES LES INSTRUCTIONS
AVANT D'INSTALLER ET
D'UTILISER L'APPAREIL,
CONSERVEZ CES INSTRUCTIONS.
LEA TODAS LAS INSTRUCCIONES
ANTES DE INSTALAR Y
UTILIZAR EL APARATO, GUARDE
ESTAS INSTRUCCIONES.

Table of Contents

Questions and Answers

  • C
    chloe20Aug 17, 2025
    Why is my Pit Boss Smoker producing excess or discolored smoke?
    • K
      Karen GregoryAug 17, 2025
      If your Pit Boss Smoker is producing excess or discolored smoke, and your food is becoming discolored, it could be due to several reasons. There might be grease build-up, so follow the Care and Maintenance instructions. The hardwood pellets might be moist; remove them from the hopper, clean it out, and replace them with dry hardwood pellets. Also, the burn pot might be blocked; clear it of any moist hardwood pellets and follow the Auger Priming Procedure. Finally, ensure the fan has sufficient air intake by checking that it is clean, working properly, and the air intake is not blocked. Follow the Care and Maintenance instructions if the fan is dirty.
  • D
    davidmichelleAug 19, 2025
    What does "Err" Error Code and Auger icon blinking mean on Pit Boss 4 Series Smokers?
    • C
      Christopher IbarraAug 20, 2025
      If you see an "Err" Error Code and the Auger icon is blinking on your Pit Boss Smoker, it means the auger motor is either jammed or not making a connection. Remove cooking components from the interior of the smoker. Turn the unit on and inspect the auger feed system. Visually confirm that the auger is dropping pellets into the burn pot. It is also possible that the auger is not primed. Before the unit is used for the first time or anytime the hopper is completely emptied out, the auger must be primed to allow pellets to fill the auger tube. Follow Auger Priming Procedure.
  • L
    Lauren SteeleAug 22, 2025
    What does "Err" Error Code and Igniter icon blinking mean on Pit Boss 4 Series Smokers?
    • J
      Jose HawkinsAug 22, 2025
      If your Pit Boss Smoker displays an "Err" Error Code and the Igniter icon is blinking, the igniter may not be working properly or making a connection. Remove cooking components from the interior of the smoker. Turn the unit on and inspect the igniter. Visually confirm that the igniter is working by placing your hand above the burn pot and feeling for heat. Disconnect and reconnect the Igniter connector to the Control Board. If it's still not operating properly, call Customer Care for assistance or a replacement part.
  • J
    jessicabrooksAug 26, 2025
    What does "Err" Error Code and Pellet icon blinking mean on Pit Boss 4 Series Smokers?
    • S
      Sarah ClarkAug 26, 2025
      If you see an "Err" Error Code and the Pellet icon blinking on your Pit Boss Smoker, it indicates a lack of fuel, poor fuel quality, or that the grill will not stay lit. Check the hopper to ensure the fuel level is sufficient and replenish if low.
  • N
    nnavarroAug 28, 2025
    What does "Err" Error Code and Fan icon blinking mean on Pit Boss Smokers?
    • I
      iwongAug 28, 2025
      If you see an "Err" Error Code and the Fan icon blinking on your Pit Boss Smoker, the fan is not working properly or not making a connection. Check the fan. Ensure it is working properly and the air intake is not blocked.
  • Y
    ywilsonAug 30, 2025
    What to do if my Pit Boss Smoker has frequent flare-ups?
    • M
      maryhansenAug 31, 2025
      Frequent flare-ups in your Pit Boss Smoker can be caused by cooking at too high a temperature, as grease has a flash point. Try cooking at a lower temperature, keeping it under 176°C / 350°F when cooking highly greasy food. Another cause could be grease build-up on cooking components, so follow the Care and Maintenance instructions.
  • P
    Pamela CookSep 2, 2025
    Why is there insufficient air flow through the burn pot of my Pit Boss Smoker?
    • N
      nicolewatkinsSep 2, 2025
      If there is insufficient air flow through the burn pot of your Pit Boss Smoker, it could be due to a few reasons. Make sure that you remove cooking components from the interior of the smoker. Check the burn pot for ash build-up or obstructions, following the Care and Maintenance instructions for ash build-up. Check the fan to ensure it is working properly and the air intake from underneath the unit is not blocked, following the Care and Maintenance instructions if it's dirty. Also, check the auger motor to confirm operation and ensure there is no blockage in the auger tube.
  • R
    Rachel NorrisSep 5, 2025
    What to do if my Pit Boss Smoker will not achieve or maintain stable temperature?
    • D
      Deanna RamirezSep 5, 2025
      If your Pit Boss Smoker will not achieve or maintain a stable temperature, check the status of the Grill Probe (Sensor). Follow Care and Maintenance instructions if it is dirty. Contact Customer Care for a replacement part if it is damaged.
  • N
    Nathan MartinSep 8, 2025
    What does "ErH" Error Code mean on Pit Boss Smokers?
    • W
      William WarrenSep 8, 2025
      If you see an "ErH" Error Code on your Pit Boss Smoker, the unit has overheated, possibly due to a grease fire or excess fuel. Press and hold the Power Button for three seconds to turn the unit off, and allow the smoker to cool. Follow the Care and Maintenance instructions.
  • M
    Mark WashingtonSep 12, 2025
    What does "ErP" Error Code mean on Pit Boss 4 Series?
    • C
      Caitlin ColemanSep 12, 2025
      If you see an "ErP" Error Code on your Pit Boss Smoker, it means the grill probe wire is not making a connection, or the grill probe is broken. Remove the access panel and check for any damage to the Grill Probe wires. Disconnect and reconnect the Grill Probe connectors to the Control Board. If the Grill Probe is broken, it needs to be replaced. Contact Customer Care for a replacement.

Summary

IMPORTANT SAFEGUARDS

SAFETY LISTING

Safety certification and compliance standards for the appliance.

DANGERS AND WARNINGS

Critical safety precautions, clearances, and fire prevention measures.

HARDWOOD PELLET FUEL

CARBON MONOXIDE

CONTROL BOARD

OPERATION

SETTING THE TEMPERATURE

USING THE MEAT PROBES

AUGER PRIMING

FIRST USE (BURN OFF)

REGULAR USE

SHUT-DOWN

CARE & MAINTENANCE

Grill Interior

Grill Exterior

TROUBLESHOOTING

WARRANTY

Pit Boss 4 Series Specifications

General IconGeneral
MaterialSteel
Ignition TypeAutomatic
Hopper Capacity18 lbs
Digital ControlYes
WheelsYes
Fuel TypePellet

Related product manuals