What do flashing dots on the Pit Boss Grill LCD screen mean?
The flashing dots on the LCD screen of your Pit Boss Grill simply indicate that the igniter is on and the unit is in Start-Up mode. This is not an error. The igniter will turn off after five minutes, and once the flashing dots disappear, the grill will begin adjusting to the selected temperature.
What to do if the Pit Boss smoker fire won't light?
If the fire in the burn pot of your Pit Boss smoker will not light, several issues could be the cause. The auger may not be primed, which means pellets are not filling the auger tube. Follow the hopper priming procedure to resolve this. Alternatively, the auger motor could be jammed; turn the unit on, set the temperature control dial to smoke, and inspect the auger feed system to confirm that the auger is dropping pellets into the burn pot. Another potential cause is igniter failure; inspect the igniter to ensure it is working and protruding approximately 13mm / 0.5 inches into the burn pot. Finally, insufficient airflow through the burn pot due to ash build-up or obstructions could be the problem; check the burn pot and fan, ensuring the air intake is not blocked.
Why is my Pit Boss Grill not maintaining temperature?
If your Pit Boss Grill isn't reaching or maintaining a stable temperature, several factors could be at play. Start by checking the burn pot for ash build-up or obstructions and ensuring the fan is working correctly with unobstructed air intake. Also, make sure the auger motor is functioning and there's no blockage in the auger tube. Next, verify that the fuel level in the hopper is sufficient and the wood pellets are of good quality, without obstructions in the feed system. Lastly, check the status of the grill probe, ensuring it's clean. If issues persist, set the grill to SMOKE and check that the flame is bright and vibrant after 10 minutes.
Why is my Pit Boss Grill producing too much smoke?
If your Pit Boss Grill is producing excessive or discolored smoke, it could be due to a few reasons. Excess grease build-up can cause this issue, so follow the Care and Maintenance instructions to clean the grill. The quality of the wood pellets also matters; remove any moist pellets and replace them with dry ones. A blocked burn pot can also lead to this problem, so clear it of ash and debris, following the Hopper Priming Procedure. Lastly, ensure the fan has sufficient air intake and is working properly; clean it if necessary, according to the Care and Maintenance instructions.
Why is my Pit Boss smoker producing too much smoke?
If your Pit Boss smoker is producing excess or discolored smoke, it could be due to several reasons. Grease build-up is a common cause, so follow the care and maintenance instructions to clean the grill. Another reason could be the quality of the wood pellets; remove any moist pellets from the hopper, clean it out, and replace them with dry wood pellets. Additionally, a blocked burn pot or insufficient air intake for the fan can cause this issue. Clear the burn pot of ash and debris, and check the fan to ensure it's working properly and the air intake is not blocked.
Why won't my Pit Boss smoker maintain a stable temperature?
If your Pit Boss smoker is not achieving or maintaining a stable temperature, several factors could be responsible. First, check the burn pot for ash build-up or obstructions and ensure sufficient airflow, inspecting the fan for proper operation and clearing any blockages. Also, inspect the auger motor to confirm operation, and ensure there is no blockage in the auger tube. Second, verify that the fuel level in the hopper is sufficient and that the wood pellets are of good quality and not too long, as poor quality or overly long pellets can obstruct the feed system. Finally, check the status of the grill probe. If dirty, follow the care and maintenance instructions. Once all the above steps have been done, start the grill, set temperature to SMOKE and wait for 10 minutes. Check that the fl...
Why does my Pit Boss smoker have no power?
If there are no power lights on the control board of your Pit Boss smoker, several factors could be the cause. Ensure the temperature control dial is set to a temperature, and the unit is plugged into a working power source, resetting the breaker if necessary. Also, verify that the GFCI is a minimum 10 Amp service and that all wire connections are firmly connected and dry. If the issue persists, check the fuse on the control board for a broken or blackened wire, replacing it if needed. If none of these steps work, the control board may be faulty and need replacement.
Why won't the fire in burn pot light on my Pit Boss Grill?
If the fire in the burn pot of your Pit Boss Grill won't light, it could be due to several reasons. First, the auger might not be primed, especially if it's the first time using the grill or the hopper was completely emptied. Follow the Hopper Priming Procedure to resolve this. Another possibility is that the auger motor is jammed; to check this, remove the cooking components, turn the unit on to SMOKE, and see if the auger is dropping pellets into the burn pot. If not, contact Customer Service. Also, the igniter may have failed. You can check if it's working by feeling for heat above the burn pot and ensuring it protrudes about 13mm (0.5 inches) into the burn pot. If it's not working, you can use the Manual Start-up Procedure temporarily, but contact Customer Service for a replacement par...
What does flashing temperature on LCD screen mean for Pit Boss Grill?
A flashing temperature on the LCD screen of your Pit Boss Grill indicates that the grill temperature is below 65°C / 150°F. This isn't necessarily an error, but it suggests a risk that the fire could go out. Check the hopper to ensure there's sufficient fuel and inspect the feed system for any obstructions. Remove the pellets and follow the Care and Maintenance instructions. Also, check the grill probe, burn pot, and fan for any issues, following the Care and Maintenance instructions as needed. Finally, confirm that the auger motor is operating correctly and that there are no blockages in the auger tube.
What does "ErP" error code mean on Pit Boss Grill?
If your Pit Boss Grill displays an "ErP" error code, it means the unit wasn't turned off properly the last time it was connected to power. This safety feature prevents an automatic restart. To fix this, press the power button to turn the unit off, wait for two minutes, and then press the power button again to turn it back on. After restarting, turn the temperature control dial to SMOKE or your desired temperature. If the error code continues to appear, contact Customer Service for further assistance.
Critical safety warnings, fire prevention, and general hazards.
Preparations, tools, and parts check before assembly begins.
Step-by-step solutions for frequent operational issues.
To Next Page
General
