Pit Boss PBV5CS - User Manual

Questions and Answers

M
matthewrobinsonAug 5, 2025
How to fix a Pit Boss Smoker when the fire won't light?
- S
  Steven MckayAug 5, 2025
  If the fire in the burn pot of your Pit Boss Smoker won't light, it might be due to several reasons. First, ensure the auger is primed, especially if it's the first use or the hopper was completely emptied. If the auger is not primed, follow the Hopper Priming Procedure. Also, inspect the auger feed system to confirm that the auger is dropping pellets into the burn pot; if it's jammed, contact Customer Service. Finally, check the igniter to ensure it's working and protruding approximately 13mm / 0.5 inches into the burn pot; if not, follow the Manual Start-up Procedure or contact Customer Service.
A
Angela HallAug 10, 2025
Why is my Pit Boss Smoker temperature unstable?
- K
  Kelly HollandAug 10, 2025
  If your Pit Boss Smoker isn't maintaining a stable temperature, several factors could be at play. First, check the burn pot for ash build-up or obstructions, ensuring sufficient airflow. Also, inspect the fan to confirm it's working correctly and the air intake isn't blocked. Next, verify the fuel level and quality, addressing any potential obstructions in the feed system. Finally, check the temperature probe for dirt. After completing these steps, start the smoker, set the temperature to SMOKE, and wait 10 minutes, checking to ensure the flame is bright and vibrant.
M
Megan RiosAug 14, 2025
Why is my Pit Boss Smoker producing too much smoke?
- D
  desiree02Aug 14, 2025
  If your Pit Boss Smoker is producing excessive or discolored smoke, there are several potential causes. Start by checking for grease build-up and following the Care and Maintenance instructions. Also, consider the quality of the wood pellets; remove any moist pellets and replace them with dry ones, cleaning out the hopper as per the Care and Maintenance instructions. Ensure the burn pot is clear of any blockages, following the Hopper Priming Procedure if needed. Lastly, check the fan to ensure it's working correctly and the air intake isn't blocked, cleaning it if dirty according to the Care and Maintenance instructions.
H
hannah40Aug 18, 2025
What to do if Pit Boss Smokers control board has no power?
- E
  Erica MorenoAug 18, 2025
  If there are no power lights on the control board of your Pit Boss Smoker, start by pressing the power button, holding it for two seconds to ensure a solid connection. Then, verify that the smoker is properly plugged into a working power source and that the GFCI outlet hasn't tripped; reset the breaker if needed, ensuring the GFCI is a minimum 15 Amp service. Next, check the fuse on the control board for any breaks or blackening, replacing it if necessary. If the issue persists, the control board may be faulty and require replacement; contact Customer Service for assistance.
S
Scott AndrewsAug 23, 2025
How to stop flare-ups in my Pit Boss Smoker?
- J
  Jennifer ZimmermanAug 23, 2025
  If you're experiencing frequent flare-ups in your Pit Boss Smoker, try cooking at a lower temperature, keeping it under 176°C / 350°F when cooking greasy foods. Also, ensure that you follow the Care and Maintenance instructions to prevent grease build-up on cooking components.
R
randalltaylorAug 27, 2025
What does it mean when my Pit Boss Smoker temperature is flashing?
- B
  Brian RamirezAug 27, 2025
  If the temperature is flashing on the LCD screen of your Pit Boss Smoker, it indicates that the smoker temperature is below 65°C / 150°F. This suggests a risk the fire could go out. Check the hopper for sufficient fuel and ensure there isn't an obstruction in the feed system. Remove the pellets and follow the Care and Maintenance instructions. Also, check the temperature probe and clean it if dirty, following the Care and Maintenance instructions. Inspect the burn pot for ash build-up or obstructions and clean as needed. Finally, check the fan to ensure it's working properly and the air intake isn't blocked.
I
Ian WardAug 31, 2025
What does 'ErH' error mean on my Pit Boss Smoker?
- S
  Steven GarciaAug 31, 2025
  If your Pit Boss Smoker displays an "ErH" error code, it indicates that the smoker has overheated, possibly due to a grease fire or excess fuel. Press and hold the power button for two seconds to turn the unit off and allow it to cool. After it cools, remove the pellets and confirm the positioning of all component parts. Once cooled, press the power button to turn the unit on, then select the desired temperature. If the error code is still displayed, contact Customer Service.