To Next PageTo Next PageWhat to do if Pit Boss Grill temperature on SMOKE is too high?
If the grill temperature on the SMOKE setting is too high, the "P" setting may be too low. Push the "P" SET button and increase the "P" setting value.
What to do if my Pit Boss Smoker shows an Err error code with the AUGER icon blinking?
This error indicates an issue with the auger. Ensure the auger is primed, especially if the unit is new or the hopper was completely emptied. Also, check for a jammed auger motor. If the auger motor is jammed, further assistance may be needed.
What to do if my Pit Boss Smoker shows an Err error code with the igniter icon blinking?
This error indicates a problem with the igniter. Inspect the igniter to ensure it is working and making a connection. If it's not operating properly or has failed, further assistance may be needed.
How to fix Err error code with FAN icon blinking on Pit Boss Grill?
An Err error code with the FAN icon blinking on your Pit Boss Grill suggests the fan isn't working properly or making a connection. Check the fan to ensure it is working correctly and that the air intake is not blocked. Inspect the fan wires for any damage. If the fan blades are dirty, follow the Care and Maintenance instructions.
What to do if my Pit Boss Smoker has no power lights on the control board?
First, ensure the unit is plugged into a working power source and reset the breaker. Make sure the GFCI is a minimum 15 Amp service. Also, check that all wire connections are firmly connected and dry. If the issue persists, the fuse on the control board might be blown and needs replacement, or the control board itself may be faulty, requiring replacement.
What does Err Error Code with IGNITOR Icon Blinking mean on Pit Boss Smokers?
If your Pit Boss Smokers displays an "Err" error code with the IGNITOR icon blinking, it means the ignitor is not working properly or not making a connection. Remove the cooking components and turn on the unit to inspect the igniter. Visually confirm that the igniter is working by placing your hand above the burn grate and feeling for heat. Also, check that the igniter is aligned with the hole in the burn grate and open to light the pellets. If it's not operating properly, contact Customer Service for assistance or a replacement part. Alternatively, the igniter may need to be replaced, so contact Customer Service for a replacement part.
What does Err Error Code with PELLET Icon Blinking mean on Pit Boss Competition Smokers?
If your Pit Boss Smokers displays an "Err" error code with the PELLET icon blinking, it indicates a lack of fuel, poor fuel quality, an obstruction in the feed system, or a jammed auger. Check the hopper to ensure the fuel level is sufficient and replenish if low. If the wood pellets are of poor quality or too long, remove them and follow the care and maintenance instructions.
What does Err Error Code with AUGER Icon Blinking mean on Pit Boss Smokers?
If your Pit Boss Smokers displays an "Err" error code with the AUGER icon blinking, it indicates that the auger is not primed or the auger motor is jammed. To resolve this, ensure the auger is primed, especially if it's the first time using the unit or the hopper was completely emptied. Follow the Hopper Priming Procedure. Also, check if the auger motor is jammed by removing the cooking components and turning on the unit to inspect the auger feed system. If the auger isn't dropping pellets into the burn pot, contact Customer Service.
What to do if the temperature readout won't adjust on Pit Boss Grill?
If the temperature readout on your Pit Boss Grill isn't adjusting, the grill probe might be dirty or broken. You can start by following the Care and Maintenance instructions to clean the probe.
What causes frequent flare-ups in my Pit Boss Smoker?
Frequent flare-ups are often due to the cooking temperature being too high or grease build-up on cooking components. Try cooking at a lower temperature, especially when cooking highly greasy foods. Also, follow care and maintenance instructions to address any grease build-up.
General| Material | Steel |
|---|---|
| Fuel Type | Wood Pellets |
| Temperature Range | 180°F to 500°F |
| Grates Material | Porcelain-Coated Steel |
| Ignition Type | Automatic |
| Warranty | 5 years |
Safety warnings related to propane gas usage and storage.
Specifications and requirements for the propane gas cylinder used with the grill.
Step-by-step instructions for safely connecting a gas cylinder to the grill.
Safe steps for lighting the grill's burners using the igniter.
Explanation of the digital control board's buttons, displays, and functions.
Essential food safety practices for cooking and handling food.
Common problems and solutions for the hardwood pellet grill operation.
