Polaris 600 RMK

Questions and Answers:

D
Daniel FernandezSep 1, 2025
What to do if my Polaris Snowmobile drive system is making noise?
- R
  Regina WilsonSep 2, 2025
  Noise in the drive system can stem from several issues: broken drive clutch components, bearing failure in the chaincase, jackshaft, or front drive shaft, drive belt surface flat spots, a loose drive chain, or a worn drive chain with broken sprocket teeth. Inspect and replace the drive belt as needed if there are flat spots. Inspect and adjust (or replace) the drive chain if it's loose. For broken clutch components, bearing failure, or a worn drive chain, it is suggested to seek assistance from your dealer.
E
Erica ReillySep 13, 2025
What to do when towing at low RPM with my Polaris Snowmobile?
- J
  Jeremy AllisonSep 13, 2025
  Do not tow in deep snow. Use fast, aggressive throttle to engage the clutch.
M
miranda16Aug 31, 2025
Why is my Polaris Snowmobile engine erratic during acceleration?
- S
  Sandra MarshallAug 31, 2025
  Erratic engine operation during acceleration or load variations can be caused by a drive clutch binding or a driven clutch malfunction. It is suggested to seek assistance from your dealer.
T
Tonya ReevesSep 15, 2025
What to do when riding with high RPM and slow speed on my Polaris Snowmobile?
- S
  Sandra WilsonSep 16, 2025
  Lower the gear ratio. Reduce RPM. Avoid riding in high ambient temperatures. Check for snow ingestion.
J
James MatthewsSep 15, 2025
What to do about poor engine performance on my Polaris Snowmobile?
- T
  Tonya BrownSep 15, 2025
  Check for fouled plugs or water, ice, or dirt in the gas tank or fuel line.
K
Kathleen ChavezSep 23, 2025
Why is there noise in my Polaris Snowmobile drive system?
- R
  Robert TaylorSep 23, 2025
  Noise in your Polaris snowmobile's drive system can stem from several issues. These include drive belt surface flat spots, and sheared teeth on the QUICKDRIVE belt, which requires replacing the QUICKDRIVE belt.
T
tina26Aug 27, 2025
Why does my Polaris Snowmobile engine lack power?
- J
  Jeremy BrownAug 28, 2025
  There are several reasons why your Polaris snowmobile engine might lack power. It could be due to fouled or defective spark plugs, which can be resolved by replacing them. Other potential causes include a fuel filter issue. For these and other issues like incorrect clutching, it is best to consult with your dealer.
D
David VillaAug 27, 2025
What to do if my Polaris Snowmobile engine backfires but fails to start?
- S
  Stephen NunezAug 27, 2025
  If the engine backfires but fails to start, the spark plug wires may be on the wrong cylinder. Reinstall spark plug wires to the corresponding cylinder.
J
Jennifer DavenportAug 26, 2025
What to do if my Polaris Snowmobile engine requires more than normal pulls to start?
- J
  Jill MitchellAug 26, 2025
  If the engine requires more than normal pulls to start, it could be due to poor gasoline or not enough fuel getting to the engine. Replace it with fresh winter fuel.
C
Carla RamosAug 25, 2025
What to do if my Polaris Snowmobile engine doesn’t turn?
- B
  Brian DayAug 26, 2025
  If the engine doesn’t turn, it could be seized due to poor lubrication, inadequate fuel supply, broken parts, or improper cooling. It is suggested to seek assistance from your dealer. Another possibility is hydrostatic lock, where fuel has entered the crankcase while the vehicle was standing or being transported. It is suggested to seek assistance from your dealer to correct the cause. Drain plug(s) are located on the lower crankcase for emergency draining.