Polaris 600 RMK

Questions and Answers:

C
Carla RamosAug 25, 2025
What to do if my Polaris Snowmobile engine doesn’t turn?
- B
  Brian DayAug 26, 2025
  If the engine doesn’t turn, it could be seized due to poor lubrication, inadequate fuel supply, broken parts, or improper cooling. It is suggested to seek assistance from your dealer. Another possibility is hydrostatic lock, where fuel has entered the crankcase while the vehicle was standing or being transported. It is suggested to seek assistance from your dealer to correct the cause. Drain plug(s) are located on the lower crankcase for emergency draining.
J
Jennifer DavenportAug 26, 2025
What to do if my Polaris Snowmobile engine requires more than normal pulls to start?
- J
  Jill MitchellAug 26, 2025
  If the engine requires more than normal pulls to start, it could be due to poor gasoline or not enough fuel getting to the engine. Replace it with fresh winter fuel.
D
David VillaAug 27, 2025
What to do if my Polaris Snowmobile engine backfires but fails to start?
- S
  Stephen NunezAug 27, 2025
  If the engine backfires but fails to start, the spark plug wires may be on the wrong cylinder. Reinstall spark plug wires to the corresponding cylinder.
T
tina26Aug 27, 2025
Why does my Polaris Snowmobile engine lack power?
- J
  Jeremy BrownAug 28, 2025
  There are several reasons why your Polaris snowmobile engine might lack power. It could be due to fouled or defective spark plugs, which can be resolved by replacing them. Other potential causes include a fuel filter issue. For these and other issues like incorrect clutching, it is best to consult with your dealer.
J
Jennifer HarrisAug 28, 2025
Why does my Polaris Snowmobile engine require more than normal pulls to start?
- A
  Allison BatesAug 28, 2025
  If your Polaris snowmobile engine requires more pulls than usual to start, it could be due to poor fuel. Try replacing it with fresh winter fuel.
A
amandameyerAug 29, 2025
What causes harsh drive clutch engagement in my Polaris Snowmobile?
- O
  oruizAug 29, 2025
  Harsh drive clutch engagement in your Polaris snowmobile can be due to a worn or narrow belt, which you can fix by replacing the drive belt.
J
john68Aug 30, 2025
What to do if my Polaris Snowmobile engine doesn't turn?
- J
  jesse34Aug 30, 2025
  If your Polaris snowmobile engine doesn't turn, it could be seized due to poor lubrication, inadequate fuel supply, broken parts, or improper cooling, or it could be experiencing hydrostatic lock, where fuel has entered the crankcase during standing or transport.
T
Tami RobinsonAug 23, 2025
What to do if my Polaris Snowmobile engine turns but fails to start?
- H
  Hannah BeckAug 23, 2025
  If your engine turns but fails to start, it could be due to a faulty ignition. Try installing new spark plug(s). If that doesn't work, check for spark; if there's no spark, seek assistance from your dealer. Another cause could be no fuel reaching the engine. Ensure the fuel valve is on, use the choke, and confirm the fuel tank has fuel. Ice in the fuel line, filter, or pump can also be a culprit; add isopropyl alcohol to the fuel system to address this. Poor engine compression, indicating a lean mixture and a major engine issue, could also be the reason, in which case you should see your dealer.
J
John RobinsonSep 1, 2025
Why is my Polaris Snowmobile engine lacking power?
- P
  pamela40Sep 1, 2025
  If your engine lacks power, it might be due to a fouled or defective spark plug, so try replacing it. Other potential causes include a fuel filter issue, which may cause loss of high RPM power, or incorrect clutching. It is suggested to seek assistance from your dealer.
D
Daniel FernandezSep 1, 2025
What to do if my Polaris Snowmobile drive system is making noise?
- R
  Regina WilsonSep 2, 2025
  Noise in the drive system can stem from several issues: broken drive clutch components, bearing failure in the chaincase, jackshaft, or front drive shaft, drive belt surface flat spots, a loose drive chain, or a worn drive chain with broken sprocket teeth. Inspect and replace the drive belt as needed if there are flat spots. Inspect and adjust (or replace) the drive chain if it's loose. For broken clutch components, bearing failure, or a worn drive chain, it is suggested to seek assistance from your dealer.