12.12. If required, the synchronized pulse of the generator signal isIf required, the synchronized pulse of the generator signal is
available at the BNC jack SYNC OUT on the front of the junction box.available at the BNC jack SYNC OUT on the front of the junction box.
If required, the synchronized pulse of the generator signalIf required, the synchronized pulse of the generator signal
is available at the BNC jack SYNC on the front of the junction box.is available at the BNC jack SYNC on the front of the junction box.
13.13. If applicable, connect the optional acoustic gate unit PSIf applicable, connect the optional acoustic gate unit PSV-V-Z-EQ to theZ-EQ to the
BNC jack GATE IN on the front of the junction box.BNC jack GATE IN on the front of the junction box.
⇔⇔
14.14. TTo control the video camera, plug ano control the video camera, plug an cable into the jack RS 232cable into the jack RS 232
on the back of the junction box and into either of the jacks Con the back of the junction box and into either of the jacks COM1 OM1 oror
COM2 COM2 on the back of the on the back of the workstaworkstation.tion.
15.15. PlPlug thug thee
cable into the BNC jack VIDEO on the back of the junctioncable into the BNC jack VIDEO on the back of the junction
box and into the 9-pin Sub-D jack AV on the back of the workstation.box and into the 9-pin Sub-D jack AV on the back of the workstation.
16.16.
Plug the Y-shapedPlug the Y-shaped
cable into the SCSI-typecable into the SCSI-type
connector ACQUISITION BOARD on the back of the junction box and intoconnector ACQUISITION BOARD on the back of the junction box and into
the two VHDIC-type connectors ACQUISITION on the back of thethe two VHDIC-type connectors ACQUISITION on the back of the
workstation.workstation.
Plug thePlug the
cable into the SCSI-type connectorcable into the SCSI-type connector
ACQUISITION BOARD on the back of the junction box and into theACQUISITION BOARD on the back of the junction box and into the
SCSI-type connector ACQUISITION on the back of the workstation.SCSI-type connector ACQUISITION on the back of the workstation.
17.17. PlPlug theug the cable into the 37-pin Sub-cable into the 37-pin Sub-D jack DIO/D jack DIO/ DAC on the backDAC on the back
of the junction box and into the 62-pin Sub-D jack of the junction box and into the 62-pin Sub-D jack DAC on the back of theDAC on the back of the
workstation.workstation.
18.18. If required, plug theIf required, plug the cable into the threecable into the three
BNC jacks OPTION 1, 2 and 3 on the back of the junction box and into theBNC jacks OPTION 1, 2 and 3 on the back of the junction box and into the
SCSI-type connector GENERATOR on the back of the workstation.SCSI-type connector GENERATOR on the back of the workstation.
⇔⇔
19.19. The umbilical cable has both a jack wiThe umbilical cable has both a jack with a straight cable exit and a jackth a straight cable exit and a jack
with a cable exit on the side. The cabling can bwith a cable exit on the side. The cabling can be freely selectede freely selected
depending on the way the scanning head has been mounted. Plug thedepending on the way the scanning head has been mounted. Plug the
cable into the industrial-style connector on the back of thecable into the industrial-style connector on the back of the
scanning head and into the industrial-style connector SCANNING HEADscanning head and into the industrial-style connector SCANNING HEAD
on the back of the junction box.on the back of the junction box.
Plug in the SCSI-type connectors with great care at the right angles so as not to damagePlug in the SCSI-type connectors with great care at the right angles so as not to damage
them!them!
The cable numbers of the generator cable have to be in accordance with the correspondingThe cable numbers of the generator cable have to be in accordance with the corresponding
number of the jack (OPTION 1, 2 or 3) on the junction box!number of the jack (OPTION 1, 2 or 3) on the junction box!
To Next Page
Loading...
