Porter-Cable 630 - Carbide-Tipped Router Bits

Pilot Panel (PP). For plunge-cutting
openings where pilot is guided by a
templet on the underside of the work.
mm \
No.
I Cutting 1
| Dia. In. Edge In. |
S
Dia. In.
hank j
Ungth la. j
Total Bit
length.In.
43842
’4
Va Va
V/a l
2%
43876 A
A
\ 1M
3
43643 A %
Vi
IK. |
IV\
43029 A '
1
A ITj
3 a
Pilot Panel Spiral Down (SDPP).
Spiral pushes chips down and out for
more efficient cutting.
"S*
1 Cutting I
1 Dia. In. Edge In,
$
Dia. In.
hank
length In.
Total Bit
longth. In.
43488
'/a 1
y, !
Va
m 3
43491 j A l i y,
YHa
3A
43031 Vi Y/a ! A
Y/a
3A
Chamfer (CH). Piloted bit for 45°
bevel cutting.
Monti
Cutting
Length In.
Shank
No.
Ola. In. Length In.
43430
y.
« 1 1
Sash Cope (SC). For coping window
rails to match bead cut.
Model Cutting
Mo. Radius lengtk In.
Dia. In. lengtk In.
43645
Ha j H a
* | 1
Carbide-
Tipped Bits
Recommended for production
cutting operations or when work¬
ing with tough, more abrasive
materials such as flake board,
plastic laminates, plywood and
composition materials.
Straight (ST). For general stock re¬
moval, slotting, grooving, rabbeting.
Modal | Cutting | Shank
No. j Dia. In. Ungth In. |
Dia. In. length In.
Adjustable (A0ST). Complete with 42109 Eccentric
Adapter to vary width of cut.
43297” | A | |
| Va | IK.
Single Flute (SFST)
43716
43717
43045
43046
43047
\y»
Y/a
i%
i%
Y/a
Sash Bead (SB). For beading inner
side of window frames.
Roman Ogee (OG). For internal
decorative work.
Model
i Cutting !
Shank
Length In.
Dia. In.
length In.
43040
Ha
Va
1
43043
% 'Ha
Va
1
Rabbeting (RT). Piloted bit for rab¬
beting or step-cutting edges.
Model
No.
Cutting
| Width In. length In.
Dio. In.
hank
Ungth la.
43453
'A
Hi
'/a 1
43458
y.
Hi
Va
1
Double Flute (DFST)
43051
Hi
Hi
A
YA
43718
'AL
A
A 1A
43300 Hi
v%
A
1 Hi
43312
y. 1
A
IA
43318
'A
1 A
1
43327
K
'Hi
A
IA
43333
y. 'Hi
A
Y/a
43052
A
A
A
YA
43053
y, s 1
A Y/a
43054
A
1
A
YA
43055
Hi Va
A
1«
43719
Vi
'Hi
A IK.
43056
Hi
Y/a
A
Y/a
43057
AS
1
A YA
43058
A Y/a
A
IA
43720
AL
YA
A
YA
43721
AX
2
A
2
43722
Va
1
A YA
43062
A
Y/a
A
IA
43063
; 1
Y/a
A YA
Screw Type (SCRU)
43703
43704
A
1
%
%
All with A"-2i
43745
Y/a %
Threaded Hole
JL
Dovetail (DT). For dovetailing joints.
Use with dovetail templet.
43048 KtS IK
; a
YA
Model Cutting
43049 A IK i A 1 Hi
Dia. In. Ungth In.
Dia, In. length In.
43050
HI 2 A Y/a 43705
A | Ht
_* 1 «
Pilot Panel Spiral Up (SUPP) w/
Mortising Boring Point. For panel
pilot routing where it is necessary to
pull chips up out of the cut.
Model
Cutting |
Shank
Total Bit
Ns.
Dia.la. Edge In.
Dia. In. length tn.j
Ungth. In.
43494 A | Y/a 1
A 1 VA 1
4
Roman Ogee (OG). Piloted bit for
decorative edging.
Solid Pilot (OGSP)
Model Catting
[ Radius Ungth In. ]
1 Shank
| Dia. In. Ungth In.
43518 '
Ka
A 1
34 1
43522 Va
Va
Va
1
Corner Round (CR). Piloted bit for
edge rounding.
Mode!
No.
Cutting
| Radius Ungth In.
s
Dia. In.
hank
Lenfih In.
43390 Hi
A
Va
l
43393
Va A
Va
i
43396
A A
Va l
43399 A
Va Va l
Rabbeting (RT). For rabbeting or step
cutting edges.
Model | Cutting |
Shank
No. | Width In. length In. |
Dia. In. Ungth In.
Solid Pilot
43706 | A* | K 2
[ .iU.I*..
*V with 42204 Pilot; V with 42207 Pilot
15