EasyManua.ls Logo

ProForm PFTL313340 - User Manual

ProForm PFTL313340
23 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
USER'S MANUAL
Visit our website at
www.proform.com
new products, prizes,
fitness tips, and much more!
Serial Number Decal
Model No. PFTL313340
Serial No.
CAUTION
Read all precautions and instruc-
tions in this manual before using
this equipment. Save this manual
for future reference.
QUESTIONS?
If you have questions, or if there
are missing or damaged parts,
we will guarantee complete sat-
isfaction through direct assis-
tance from our factory.
TO AVOID DELAYS, PLEASE
CALL DIRECT TO OUR TOLL-
FREE CUSTOMER HOT LINE.
The trained technicians on our
Customer Hot Line will provide
immediate assistance, free of
charge to you.
CUSTOMER HOT LINE:
1-888-533-1333
Mon.–Fri., 6 a.m.–6 p.m. MST

Table of Contents

Questions and Answers

  • A
    amandageorgeAug 11, 2025
    How to fix ProForm PFTL313340 Treadmill when the power does not turn on?
    • J
      Jonathan OchoaAug 12, 2025
      First, ensure the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet, using only a single-outlet surge suppressor that meets all specifications. Also, check that the key is fully inserted into the console. Finally, check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes, the circuit breaker has tripped. To reset it, wait five minutes and then press the switch back in.
  • R
    Richard BarrettAug 18, 2025
    What to do if my ProForm PFTL313340 Treadmill turns off during use?
    • J
      Jennifer MorrowAug 18, 2025
      If your ProForm Treadmill turns off during use, first check the reset/off circuit breaker located on the treadmill frame near the power cord. If the circuit breaker has tripped, wait five minutes and then press the switch back in. Also, make sure that the power cord is plugged in; if it is, unplug it, wait five minutes, and then plug it back in. Another thing to check is the key: remove it from the console, and then reinsert it fully.
  • R
    Robert BerryAug 25, 2025
    What to do if the console display on my ProForm PFTL313340 isn't working right?
    • M
      Michelle McmillanAug 25, 2025
      Remove the key from the console and unplug the power cord. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until the Magnet is aligned with the Reed Switch. Make sure that the gap between the Magnet and the Reed Switch is about 1/8”. If necessary, loosen the Screw, Retighten the Screw. Re-attach the Hood, and run the treadmill for a few minutes to check for a correct speed reading.
  • O
    Omar GreeneAug 29, 2025
    How to adjust a ProForm Treadmill walking belt that is off-center or slips?
    • R
      Robert FarrellAug 30, 2025
      If the walking belt is off-center, remove the key and unplug the power cord first. If the belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Plug the power cord back in, insert the key, and run the treadmill for a few minutes. If the walking belt slips when walked on, remove the key and unplug the power cord first. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Plug in the power cord, insert the key, and carefully walk on the treadmill for a few minutes.
  • S
    Stephanie WelchSep 4, 2025
    Why does the ProForm PFTL313340 Treadmill walking belt slow down when I walk on it?
    • A
      Amy JonesSep 4, 2025
      The walking belt might be slowing down due to a few reasons. First, ensure you're using only a single-outlet surge suppressor that meets all specified requirements. Also, the walking belt might be overtightened. To resolve this, remove the key and unplug the power cord. Using the allen wrench, turn both rear roller adjustment bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each side of the walking belt 2 to 3 inches off the walking platform. Plug in the power cord, insert the key, and run the treadmill for a few minutes.

ProForm PFTL313340 Specifications

General IconGeneral
Weight203 pounds
Motor2.75 CHP
Running Area20 x 60 inches
DeclineNo
Display7-inch backlit display
Programs50+
Heart Rate MonitoringYes
FoldingYes
Incline0-12%
Speed0 – 12 MPH Digital Speed Control
User Weight Capacity300 lbs
Speed Range0 – 12 MPH
Incline Range0 – 12%
Weight Capacity300 lbs

Related product manuals