Need help?Do you have a question about the QNAP TS-453U and is the answer not in the manual?
General| RAID levels | 1, 5, 6, 10 |
|---|---|
| RAID support | Yes |
| Storage drive size | 2.5/3.5 \ |
| Storage drive capacity | 0 GB |
| Supported file systems | ext3, ext4, FAT32, HFS+, NTFS |
| Storage drive interface | Serial ATA III |
| Storage drives installed | No |
| Supported storage drive types | HDD & SSD |
| Total installed storage capacity | 0 TB |
| Number of storage drives installed | 0 |
| Number of storage drives supported | 4 |
| Processor model | - |
| Processor family | Intel® Celeron® |
| Processor frequency | 2 GHz |
| Flash memory | 512 MB |
| Memory slots | 2 |
| Internal memory | 4 GB |
| Internal memory type | DDR3L |
| Maximum RAM supported | 8 GB |
| Ethernet LAN data rates | 10, 100, 1000 Mbit/s |
| Supported network protocols | CIFS/SMB, AFP (v3.3), NFS(v3), FTP, FTPS, SFTP, TFTP, HTTP(S), Telnet, SSH, iSCSI, SNMP, SMTP, SMSC |
| USB 2.0 ports quantity | 1 |
| Chassis type | Rack (1U) |
| Cooling type | Active |
| Fan diameter | 40 mm |
| Product color | Black |
| Type | NAS |
| Device class | Small & Medium Business |
| Backup features | Cloud, iSCSI LUN |
| Security algorithms | 256-bit AES, FIPS 140-2, HTTPS, SSH, SSL/TLS |
| Operating system version | 4.1 |
| Operating system installed | QNAP Turbo System |
| Fan voltage | 12 V |
| AC input voltage | 100-240 V |
| AC input frequency | 50 - 60 Hz |
| Power supply location | Built-in |
| Power consumption (sleep) | 23.54 W |
| Power consumption (typical) | 39.86 W |
| Power supply unit (PSU) capacity | 250 W |
| Cables included | AC, LAN (RJ-45) |
Weight and Dimensions| Depth | 499 mm |
|---|---|
| Width | 439 mm |
| Height | 44 mm |
Information regarding FCC compliance for QNAP NAS devices.
Details compliance with FCC Part 15 for Class A digital devices.
Explains beep sounds and their meanings for system status.
Instructions for upgrading memory on specific NAS models.
Instructions for upgrading memory on TBS-453A NAS model.
Memory upgrade steps for various QNAP NAS models.
RAM module installation procedure for the TS-1635 model.
Memory upgrade guide for TVS-473, TVS-673, and TVS-873 models.
Steps to upgrade memory for specific TS/TVS series NAS models.
Procedure for upgrading memory on TS-251/TS-451 series NAS models.
Installing RAM on the IS-453S model.
Installing network expansion cards in specific NAS models.
Installing network expansion cards in the TS-1635 model.
Procedure for installing network expansion cards in TVS-473, TVS-673, TVS-873.
Installing expansion cards on TS/TVS rackmount NAS models.
General steps for installing hard drives into the NAS.
Hard drive installation for a wide range of QNAP NAS models.
Procedure for installing hard drives in the TS-1635 NAS model.
Steps for installing hard drives in TS-453Bmini and TS-453Mini models.
Installing hard drives in TVS-473, TVS-673, and TVS-873 models.
Hard drive installation guide for TS-112P, TS-212P, and TS-251C models.
Hard drive installation for TAS-168, TAS-268, TS-128, TS-228 models.
Procedure for installing hard drives in the IS-453S NAS model.
Information on hot-swapping hard drives and compatibility.
Installing heat sinks onto M.2 SSD controllers for reliable operation.
General guide for installing M.2 SSDs in compatible NAS models.
Procedure for adding/replacing M.2 SSD modules on TBS-453A.
Installing M.2 SSDs in TVS-473, TVS-673, and TVS-873 models.
Using the LCD panel for system settings and information on QTS 4.3.0+.
How to view system IP addresses using the LCD panel.
Navigating the LCD panel to view and configure system settings.
Steps to install a redundant power supply in 1U Turbo NAS models.
Replacing a failed power supply in specific 2U/3U Turbo NAS models.
Contact information and service hours for technical support in the USA and Canada.
To Next Page
