To Next PageTo Next PageWhat to do if my Rain Soft Water System has poor water quality?
If you are experiencing poor water quality with your Rain Soft Water System, there are a few potential causes. First, the raw water source might have changed, requiring a new water analysis from your RainSoft dealer. Second, check if the bypass valve is closed; if not, close it. Finally, ensure the power supply is properly connected.
How to troubleshoot loss of water pressure in Rain Soft Water System?
If you're experiencing a loss of water pressure with your Rain Soft Water System, the first step is to bypass the system. If the problem persists after bypassing, it is not related to a RainSoft product; check your water distribution system. If bypassing resolves the issue, contact your RainSoft Dealer for service. Another potential cause is low pressure to the unit.
How to fix Rain Soft TC that regenerates at the wrong time?
If your Rain Soft Water System regenerates at the wrong time, it is possible that the computer is not set properly. Reset the time of day/hour of regeneration.
What causes constant flow to the drain in Rain Soft TC?
Constant flow to the drain in your Rain Soft Water System can be caused by foreign material in the valve, which requires cleaning by your RainSoft Dealer. Another possible cause is excessive water pressure; in this case, install a pressure regulator.
General| Brand | Rain Soft |
|---|---|
| Model | TC Series |
| Category | Water System |
| Language | English |
Details limitations based on hardness, chlorine/chloramine levels, and iron content.
Specifies required pipe sizes for plumbing connections.
Details the acceptable range of water pressure for the system.
Specifies the operational temperature range for the unit.
Outlines the necessary electrical supply for system operation.
Explains the function of the bypass valve for service or emergencies.
Advises on the condition of existing plumbing for compatibility.
Lists various installation and operational specifications.
Explains how pressure and iron content affect system efficiency.
Explains how pressure and iron content affect system efficiency.
Explains how pressure and iron content affect system efficiency.
Details how to clean and lubricate the regeneration valve.
Recommends periodic water testing for performance monitoring.
Certified by WQA to NSF/ANSI Standard 44 for specific performance claims.
Certified by WQA to NSF/ANSI standard 372 for "lead free" compliance.
Certified by WQA to CSA B483.1 Standard.
General safety measures to follow during installation.
Recommends testing raw water for contaminants like iron.
Guides on verifying water pressure suitability for installation.
Provides criteria for selecting an appropriate installation location.
Step-by-step instructions for attaching the valve head.
Instructions for safely shutting off water and draining the system.
Instructions for setting up a separate line for untreated water.
Details on connecting the yoke and bypass valve.
How to set the bypass valve to the bypass position.
Instructions for connecting the drain line and air gap.
Steps for installing the safety float in the brine tank.
Instructions for connecting the brine line to the valve and float.
Guidance on routing the brine overflow line to a drain.
Steps for connecting the electrical components and plugging in the unit.
Procedure to turn on water and inspect for leaks.
Instructions for flushing debris from the plumbing and system.
How to move the bypass valve to the service position.
Guidance on flushing the hot water heater after system setup.
Directs user to settings for adding salt and programming.
Procedure for sanitizing the water conditioner.
Guide on adjusting the system's clock time.
How to set the desired time for system regeneration.
How to configure the frequency of regeneration cycles.
Instructions for setting the amount of salt used per regeneration.
How to manually initiate a regeneration cycle.
Detailed steps for installers to program the control unit.
Navigating the home screen for basic settings adjustment.
Guide to estimating daily water consumption.
Method for calculating daily hardness and iron load.
How to determine the optimal regeneration frequency.
Lists common symptoms, their causes, and solutions.
Details the terms and conditions of the product warranty.
Diagram showing the assembly of the valve components.
Lists all components of the valve with part numbers.
Diagram illustrating the assembly of the control unit.
Lists all components of the control unit with part numbers.
