Ransomes MP653 - 11 FUSES, RELAYS AND CONTROLLER; 11.1 FUSE AND RELAY;COMPONENT IDENTIFICATION

138 pages

Save Page as PDF

To Next Page

To Previous Page

en-120

11 FUSES, RELAYS AND CONTROLLER

123456

5.1

5.2

11.1 FUSE AND RELAY/COMPONENT IDENTIFICATION _________________________

123456

Main Page

Table of Contents2
Safety, Operation & Maintenance Manual3
Product Identification4
Guidelines for the Disposal of Scrap Products6
During Service Life6
End of Service Life6
Parts Manual7
Key Numbers7
How to Operate Safely9
Safe Operation9
Preparation9
Operation10
Safe Handling of Fuels11
Maintenance and Storage11
When You Put the Mower on a Trailer12
Important Safety Notes13
Safety Decals16
Instruction Decals18
Operator Workstation20
Control Panel21
Starter Key Switch22
Throttle Control Rotary22
Park Brake22
Hazard Warning Switch (Optional)22
Cutter Switch (Pto)23
4Wd in Reverse Switch23
Light Switch (Optional)23
Rotating Beacon (Optional)23
Cruise Control Switch24
Transport Lock Switch24
Dpf Switch24
Auxilary Hydraulic Services Kit Switch (Optional)24
Visual Display25
Startup Screen25
Warning / Service Screen25
Home Screen26
Engine Start26
The Engine will Not Start26
Main Menu27
Clock & Date Adjust27
Service Menu27
Fault Log27
Time until Service28
Vehicle Diagnostics28
I/O Diagnostics29
Settings29
Measurement Units29
Vehicle Modes36
Cruise Control36
Adapticut37
Vehicle Speed38
Display Inclines38
Auto Idle38
Cross Cut39
Inclinometer39
Set Default Parameters39
Change Pin40
Brightness40
Language Menu40
Warning Screens41
Slope Angle Display41
Warning Slope Angle - Inhibit Cut42
Warning Slope Angle - Stop Cut42
Warning Oil Pressure Fault42
Warning Engine Overheat43
Warning Engine Fault43
Warning Battery Fault43
Warning Low Hydraulic Oil44
Warning Charge Filter Blocked44
Warning Service Required44
Emission Fault - Delta-P Sensor or Abnormal Delta-P44
Emission Fault - Egr Nox Control45
Emission Fault - Maf Sensor45
Emission Fault - Dpf Sensor45
Clean Dpf Ash45
Ecu Communication Fault46
Mcu / Display Communication Fault46
Cooling Fan Operation47
Lift/Lower Switch's48
Indicator Lamps48
Weight Transfer Button48
Traction Pedal49
Driving49
Mowing49
Steering Tilt Control50
Horn50
Power Outlet50
Park Brake Release Valve51
Free Wheel51
The Free Wheel Facility Is for Recovery Purposes Only51
Lighting Kit (Optional)52
Seat Right Hand Arm Rest & Pod52
Cabin Controls53
Daily Inspection55
Operator Presence and Safety Interlock System56
Procedure for Operation57
To Fit the Cutter Decks to the Machine58
Operation of the Machine64
How to Start the Engine64
How to Drive64
How to Mow65
To Stop the Engine65
To Remove a Blockage from Cutting Units65
Transporting on a Trailer66
Slinging and Jacking the Machine66
Mowing on Slopes67
How to Calculate a Slope68
Slope Calculation Chart69
Rops General Precautions70
Engine Auxiliary Belt71
Weight Transfer Adjustment71
Axle Stop Adjustment71
Steering Shaft Adjustment72
Height of Cut Adjustment73
Height of Cut Adjustment (Front Deck)73
Height of Cut Adjustment (Mp653 Wing Cutter Deck)74
Height of Cut Adjustment (Mp653Xc Wing Cutter Decks)75
General Instructions for Grammer Seats76
Seat (Grammer Msg85)77
Air Suspension Seat (Grammer Msg75 -521)78
Weight Adjustment78
Front and Back Adjustment78
Backrest Extension78
Lumbar Support (Option)79
Left Hand Armrests79
Armrest Adjustment79
Backrest Adjustment79
Maintenance80
Air Suspension Seat (Grammer Msg95 -721)81
Weight Adjustment81
Height Adjustment81
Armrests Adjustment (Option)82
Armrest (Option)82
Backrest Adjustment (Option)82
Lumber Support (Option)82
Backrest Adjustment (Option)83
Fore / Aft Adjustment (Option)83
Multifunction Armrest (Option)83
Maintenance84
Maintenance and Lubrication Charts86
Machine Service Interval Chart86
Fluid Requirements86
Engine Service Interval Chart88
General Precautions90
Engine90
Engine Lubrication91
Pin Engine Coolant92
Hydraulic System94
Hydraulic Filter95
Hydraulic Test Ports96
Fuel97
Fuel System98
Air Cleaner99
Battery100
Charge the Battery101
Engine Exhaust101
Diesel Particulate Filter102
Hydraulic Hoses103
Wheel Alignment Procedure104
Steering Rod and Steering Link Check105
Tyres106
Wheel Mounting Procedure106
Blade Change107
Inspecting Blades108
Sharpening Blades108
Folding Rops109
Care and Cleaning110
Mower Storage111
Lubrication of Cutting Unit112
Engine Problem Diagnostics114
Quality of Cut Problem Solving116
The Step Cut117
Fuse and Relay/Component Identification124
Fuses125
Relays125
Engine Specification127
Dimensions & Weights (Rops Machine)128
Dimensions & Weights (Cab Machine)130
Machine Specification132
Vibration133
Noise134
Slopes134
Cutting Performance134
Cutter Deck Specification135
Recommended Lubricants136
Accessories136
Guarantee137
Warranty137
Service137

Ransomes MP653 - 11 FUSES, RELAYS AND CONTROLLER; 11.1 FUSE AND RELAY;COMPONENT IDENTIFICATION

Table of Contents

Other manuals for Ransomes MP653

Related product manuals