Raven SCS 5000 Series - Page 21

104 pages

To Next Page

To Previous Page

Manual No. 016-0159-925 13

CAN Networking and CAN Data Menu

FIGURE 4. SCS 4000/5000 Multi-Product CAN Control System Two Granular Products

Main Page

Default Chapter3
- Table of Contents3
- Calibration Reference Sheet7
  - Edit Mode7
- Unit Definitions and Conversions8
  - Unit of Measure Definitions8
  - Unit of Measure Conversions8
Chapter 1 Important Safety Information9
- Safety Information9
  - Hydraulic Safety10
  - Electrical Safety10
Chapter 2 Introduction11
- Introduction11
  - Sprayer & Spreader Control Systems11
- System Components12
- SCS 4000/5000 Series Console Feature Overview13
- Care and Use15
- Technical Specifications15
- Updates16
CAN Networking and CAN Data Menu17
Chapter 3 CAN Networking and CAN Data Menu19
- Detecting CAN Nodes25
- Programming Canbus Nodes26
- CAN Troubleshooting26
  - CAN Node Off-Line Errors26
Chapter 4 Installation29
- Mount the SCS Console30
- Cable and Power Connections30
- Installation29
  - Install the SCS Console29
Chapter 5 Initial Startup & Console Programming35
- Initial Calibration Sequence35
  - Reprogramming Initial Settings39
- Console Programming40
- Self Test Mode42
- Decimal Shift43
Chapter 6 Data Menu45
- Serial Submenu45
- Additional Serial Options46
  - Scs 4000/4070/500046
  - Scs 4400/460046
- Product Submenu47
  - Page49
  - Page51
- Console Submenu53
- CAN Submenu54
- Calibration Summary55
- Data Logger (4400 and 4600 Only)55
  - Setup55
- SCS Alarm Definitions57
Chapter 7 Console Calibration59
- Wheel Drive Speed Sensor60
- Speedometer Drive Speed Sensor61
- Liquid Applications62
- Dual Loop Control Mode Settings65
  - Flow Cal65
  - System (Pressure) Gain66
- Granular Applications66
- Additional Calibration Data68
  - Entering Tank Volume68
  - Zero Out" Display Information68
- Console Calibration59
  - Speed Cal59
Job Setup & Field Testing69
- Liquid Applications69
- Granular Applications71
Chapter 8 Job Setup & Field Testing71
Chapter 10 Testing Extension Cables74
Chapter 9 Troubleshooting75
Testing Extension Cables77
- Speed Sensor Cables77
  - Testing the Speed Sensor Cable77
- Flow Meter/Encoder Cables78
  - Testing the Flow Meter Cable78
Connecting an SCS Console to a Raven Field Computer79
- Firmware Requirements79
  - Operation Guidelines79
- Field Computer Set up80
  - Viper Pro80
  - Envizio Pro or Envizio Pro II80
Chapter 11 Connecting an SCS Console to a Raven Field Computer81
- Cruizer or Cruizer II82
Chapter 12 Flow Meter Maintenance & Adjustment Procedure85
Chapter 13 Ratio Rate Feature87
- Ratio Rate Feature87
Chapter 14 Remote Switch Option89
- Remote Switch Option89
SCS 4000/5000 Series Firmware Update Procedure91
- Using a USB to Serial Adapter91
  - USB to Serial Adapter Preparation91
- Serial Console Updater Utility93
Chapter 15 SCS 4000/5000 Series Firmware Update Procedure93
- Hyperterminal95
Serial Interface & Data String Formats97
- Remote Computer to SCS Console97
  - Rate Change Request97
- SCS 4000/4070/5000 Console to Remote Computer98
- SCS 4400/4600 Console to Remote Computer99
Chapter 16 Serial Interface & Data String Formats99

Raven SCS 5000 Series - Page 21

Table of Contents

Related product manuals