How to troubleshoot Raymarine Marine Equipment that won't start?
If your Raymarine Marine Equipment system or part of it does not start up, there could be a power supply problem. Check the relevant fuses and breakers. Also, verify that the power supply cable is in good condition and that all connections are tight and free from corrosion. Finally, ensure that the power source provides the correct voltage and sufficient current.
Why does my Raymarine Marine Equipment display behave erratically?
If your Raymarine Marine Equipment display behaves erratically with frequent unexpected resets, system crashes, or other erratic behavior, check the relevant fuses and breakers. Ensure that the power supply cable is sound and that all connections are tight and free from corrosion. Also, verify that the power source provides the correct voltage and sufficient current. You may need to perform a factory reset. For software issues, go to www.raymarine.com and click on support for the latest software downloads.
How to fix incorrect radar bearing on Raymarine Marine Equipment?
If the radar bearing of a target on the Raymarine Marine Equipment screen is incorrect, check and adjust the radar bearing alignment.
Why is the image on my Raymarine Marine Equipment too dark?
If the image on your Raymarine Marine Equipment is too dark or too light, use the brightness controls at the display to adjust accordingly. Adjust the contrast and brightness of the image using the appropriate menu in the thermal camera application. A different Scene Mode setting may be more appropriate for the current conditions; use the SCENE button to adjust.
Why are the controls on my Raymarine Marine Equipment erratic?
If you are experiencing erratic or unresponsive controls on your Raymarine Marine Equipment, check that the controller and thermal camera are correctly connected to the network. Verify the status of the Raymarine network switch and ensure that SeaTalkhs/RayNet cables are free from damage. Ensure that no other controllers are in use at the same time to avoid control conflicts. Check the power/network cabling to the controller and PoE injector (if PoE is only used with optional Joystick Control Unit). If available, check other controllers to eliminate the possibility of a more fundamental camera fault.
What to do if video is not displayed on Raymarine Marine Equipment?
If the video is not displayed on your Raymarine Marine Equipment, the camera may be in Standby mode. Use the camera controls (either the thermal camera application or JCU) to wake the camera from standby. Check the thermal camera video cables to ensure they are sound and properly connected, and ensure that the video is connected into video input 1 at the multifunction display or GVM. Also, ensure that the correct video input is selected at the display. Check the power connections to the camera and JCU/PoE injector (if used), and ensure that the power switch/breaker is on and the fuse/breaker is in good condition.
Why isn't the touchscreen working on my Raymarine Marine Equipment?
If the touchscreen on your Raymarine Marine Equipment does not operate as expected, ensure that the touch lock is disabled. The touch lock can be turned off on the home screen using the Joystick. Also, make sure you are operating the screen with bare fingers, as gloves may prevent correct operation. Calibrate the touchscreen using the setup menus. If there are saltwater deposits on the screen, carefully clean and dry the screen according to the provided instructions.
What causes Raymarine Marine Equipment radar to not initialize?
If the radar on your Raymarine Marine Equipment will not initialize and the Voltage Control Module (VCM) is stuck in “sleep mode”, check the power connection at the VCM. Ensure the voltage at the input is 12/24V and the voltage at the output is 40V. The issue could be due to an intermittent or poor power connection.
Why is instrument data missing from all Raymarine Marine Equipment displays?
If instrument, engine, or other system data is unavailable at all displays on your Raymarine Marine Equipment, check the data bus (e.g., SeaTalkng) wiring and connections to ensure data is being received at the display. Verify the overall integrity of the data bus (e.g., SeaTalkng) wiring. Check the source of the missing data (e.g., ST70 instrument or engine interface) to ensure it is operating. Also, check the power to the SeaTalk bus. If a software mismatch between equipment is suspected, contact Raymarine technical support.
What to do if Raymarine Marine Equipment shows no data or scanner message?
If you have no data or are receiving a 'No scanner' message on your Raymarine Marine Equipment, begin by checking the scanner power supply cable to ensure it is sound and that all connections are tight and free of corrosion. Check the relevant fuses and breakers. Ensure the power source provides the correct voltage and sufficient current, using a voltage booster if needed. Verify that the scanner is correctly connected to a Raymarine network switch or SeaTalkhs crossover coupler, as applicable, and check the status of the Raymarine network switch. Make sure SeaTalkhs/RayNet cables are free from damage and the scanner pedestal switch is in the ON position. If a software mismatch between equipment is suspected, contact Raymarine technical support.
General| Display Size | 9 inches |
|---|---|
| Display Resolution | 800 x 480 pixels |
| Display Type | LCD |
| Touchscreen | Yes |
| Waterproof Rating | IPX6 and IPX7 |
| GPS | Yes |
| Cartography | Navionics, C-MAP |
| Sonar | Yes |
| Operating Temperature | -15°C to 55°C |
| Networking | NMEA 2000, Wi-Fi |
| Storage Temperature | -25°C to 70°C |
To Next Page
