Raymarine axiom 12 - User Manual

Questions and Answers

J
jacob62Aug 19, 2025
What to do if Raymarine GPS product will not boot up?
- R
  Rebecca GrahamAug 19, 2025
  If your Raymarine GPS product won't boot up, it could be due to power supply and connection issues. Refer to the solutions for 'Product does not turn on or keeps turning off'. Alternatively, the software might be corrupted. Try re-flashing the latest software from the Raymarine website. As a last resort, on display products, you can perform a ‘Power on Reset’, but this will delete all settings, presets, and user data.
H
harrischristianAug 23, 2025
Why does my Raymarine GPS keep turning off?
- A
  Anthony SpencerAug 25, 2025
  Your Raymarine GPS might be turning off due to several reasons: a blown fuse or tripped breaker (check and replace if necessary, and inspect for cable damage if it keeps blowing), a poor or damaged power supply cable or connection (ensure the cable is fully inserted, check for damage or corrosion, and flex the cable to check for loose connections), incorrect power connection (ensure the installation instructions were followed), or an insufficient power source (check the power supply voltage with a multi-meter under load).
B
Bernard WilsonAug 26, 2025
How to fix a Raymarine axiom 12 Monitor that won't turn on?
- B
  brandy34Aug 26, 2025
  If your Raymarine Monitor doesn't turn on or keeps turning off, here are some things to check: * Make sure the relevant fuses and breakers are in good condition and properly connected; replace them if needed. * Verify the power cable is correctly oriented, fully inserted into the display connector, and locked in place. * Confirm the power supply is wired correctly, referring to the installation instructions if necessary.
A
andersonstephanieAug 30, 2025
What to do if Raymarine Monitor connection is slow or keeps dropping?
- L
  Laura CoxAug 30, 2025
  If your Raymarine Monitor's connection is slow or keeps dropping, it might be due to: * Wi-Fi performance degrades over distance. Move devices closer together. * Interference being caused by other Wi-Fi enabled or older Bluetooth enabled devices. Change the Wi-Fi Channel of the device you are trying to connect to and retry the connection. * Interference from devices on other vessels. Change the Wi-Fi Channel of the device you are trying to connect to and retry the connection.
C
christopher01Sep 1, 2025
How to troubleshoot a Raymarine axiom 12 Monitor that cannot find a network?
- A
  Amy AlvarezSep 1, 2025
  If your Raymarine Monitor cannot find a network, consider the following: * Ensure Wi-Fi is enabled on both Wi-Fi devices and rescan available networks. * Some devices may automatically turn off Wi-Fi when not in use to save power. Power cycle / reboot devices and rescan available networks. * Try to enable broadcasting of the device’s network using the Wi-Fi settings on the device you are trying to connect to. * Move devices closer together or, if possible remove the obstructions and then rescan available network.
J
Jeffrey ClineSep 5, 2025
What to do if Raymarine Monitor touchscreen is not working?
- L
  Leslie ScottSep 5, 2025
  If the touchscreen on your Raymarine Monitor is not working as expected: * Check if TouchLock is enabled. Swipe your finger from left to right across the Power button swipe area to de-activate the TouchLock. * Ensure you are operating the screen with bare fingers. Bare fingers must make contact with the screen for correct operation. * If there are water deposits on the screen, carefully clean and dry the screen in accordance with the instructions provided.
C
Charles LeeSep 9, 2025
Why does my Raymarine axiom 12 display behave erratically?
- D
  duncancynthiaSep 9, 2025
  If your Raymarine Monitor is behaving erratically with frequent unexpected resets, system crashes, or other erratic behavior, consider the following: * Intermittent problem with power to the display: Check relevant fuses and breakers. * Software mismatch on system (upgrade required): Go to www.raymarine.com and click on support for the latest software downloads. * Corrupt data / other unknown issue: Perform a factory reset. Important: This will result in the loss of any settings and data (such as waypoints) stored on the product.
Y
yboydSep 12, 2025
Why is the Raymarine axiom 12 mobile application running slowly or not at all?
- T
  Tina BonillaSep 12, 2025
  If the mobile application for your Raymarine Monitor is running slowly or not at all, check these things: * Raymarine app not installed: Install mobile app from relevant app store. * Raymarine app version not compatible with MFD software: Ensure mobile app and MFD software are latest available versions. * Mobile apps not enabled on MFD: Enable “Viewing only” or “Remote Control” as required in the Mobile Apps setting on your MFD.
H
Heather MartinezSep 14, 2025
What to do if Raymarine axiom 12 Monitor will not start up (restart loop)?
- C
  Cathy JarvisSep 14, 2025
  In the unlikely event that the Raymarine Monitor will not start up (restart loop) due to software corruption, try downloading and installing the latest software from the Raymarine website.
H
Holly SalinasSep 16, 2025
Why does my Raymarine axiom 12 show a “No Fix” GNSS status?
- K
  kmortonSep 16, 2025
  The “No Fix” GNSS status icon on your Raymarine Monitor may be displayed due to: * Geographic location or prevailing conditions preventing satellite fix. Check periodically to see if a fix is obtained in better conditions or another geographic location. * GNSS (GPS) connection fault. Ensure that external GNSS connections and cabling are correct and fault free. * External GNSS (GPS) receiver in poor location. Ensure GNSS (GPS) receiver has a clear view of the sky. * GNSS (GPS) installation problem. Refer to the installation instructions.

Summary

AXIOM Installation Guide

Important Information and Warnings

Crucial warnings and guidelines for safe product installation and operation, including RF compliance.

Product Documentation and Applicable Models

Overview of available manuals, applicable MFD models, and compatible transducers.

Installation Location and Mounting Options

Guidance on selecting installation location and various mounting methods like Trunnion, Flush, and Surface.

Connection Procedures for MFDs

Details on connecting power, NMEA 2000, transducers, networks, and accessories to the MFD.

Display Maintenance and Cleaning

Recommended procedures for servicing, routine checks, and cleaning the display.

Troubleshooting Common Issues

Solutions for power, GNSS, sonar, Wi-Fi, and touchscreen problems.

Technical Support and Learning Resources

Contact information for support, plus links to tutorials, FAQs, and forums.

Technical Specifications Overview

Key technical details for Axiom MFDs, sonar, and GNSS receiver.

Spares and Accessories Catalog

Lists available spare parts, accessories, and cables for Axiom systems.

RV-100 Transducer Installation Guide

Important Information and Warnings

Critical safety warnings, operation guidelines, and documentation access for the RV-100 transducer.

Applicable Product and Required Tools

Identifies the RV-100 transducer and lists essential tools for its installation.

Transducer Testing and Location Selection

Procedures for testing transducer operation and selecting an optimal mounting location.

Transducer Mounting and Cable Routing

Steps for mounting the bracket, transducer, and routing the cable, including escutcheon plate.

Connector Locking Collar Attachment

Step-by-step guide for securely attaching the locking collar to the transducer connector.

Finalizing Transducer Mounting

Final steps to secure the transducer and hanger after performance testing.

Raymarine axiom 12 Specifications

General

Display Type	LCD
Operating System	LightHouse 3
Resolution	1280 x 800
Touchscreen	Yes
Operating Temperature	55°C
Waterproof Rating	IPX6
Touch Screen Type	Capacitive
Networking	Ethernet, NMEA 2000
Video Input	Yes
GPS	Built-in GPS
Cartography	Supports Navionics and LightHouse charts
Internal Storage	16GB
Display Size	12.1 inches