Why does my Red Lion Water Pump lose prime?
Your Red Lion Water Pump might be losing prime because of air leaks in the suction line; inspect the suction line for these leaks. Another cause could be the well drawing down too far, so monitor the well draw down. A faulty foot valve could also be the reason; consider replacing it.
What to do if Red Lion Water Pump is losing pressure or unable to prime in well point installations?
For well point installations where the Red Lion Water Pump is losing pressure or is unable to prime, have an electrician install a low pressure cut-off switch to shut down the pump prior to critical failure. Install or adjust a restrictor valve to offset available capacity. Add a larger tank (20 gallon or larger) for additional capacity.
Why does my red lion RJS-PREM start and stop too often?
Your Red Lion Water Pump might be starting and stopping too often due to several reasons. It could be a faulty air volume control, which needs replacement or repair. Air leaks in the tank above the water level could also be the cause, so check for those. The pressure switch might be incorrectly set, requiring adjustment. The tank could also be waterlogged or incorrectly charged, necessitating a recharge or assessment. Finally, a leaking or stuck-open foot valve could be the culprit, requiring inspection and repair.
What to do if my Red Lion Water Pump delivers water but not at rated capacity?
If your Red Lion Water Pump isn't delivering water at its rated capacity, several factors could be responsible. Check for leaks in the suction or discharge line and repair them. The foot valve, suction line, impeller, or nozzle might be partially plugged, so clear any blockages. Ensure the suction lift meets recommended levels. Verify the impeller rotation and speed are correct. Also, check if the venturi or diffuser is plugged and unplug it if necessary. Confirm the motor is wired for the proper voltage and that the line voltage at the motor is correct. Lastly, if a filtration cartridge is used, ensure it's correctly installed or needs changing.
How to fix a Red Lion Water Pump motor that will not start?
If your Red Lion Water Pump motor isn't starting, it could be due to a few reasons. First, check for blown fuses, open switches, or loose connections preventing power from reaching the pressure switch; replace any blown fuses, ensure switches are closed, and tighten connections. Another possibility is that the pump pressure switch isn't closed, so verify its position.
What to do if my red lion RJS-PREM Water Pump fails to deliver water?
If your Red Lion Water Pump isn't delivering water, make sure the pump is completely primed. Also, the suction lift might be too great, and you may need to reduce it. Check that the foot valve is submerged, not buried in mud, and not plugged. Finally, make sure the restrictor valve is open.
Understand safety symbols and signal words for potential hazards.
Ensure all electrical work complies with codes and is done by a licensed professional.
Measures to prevent electric shock, including grounding, disconnects, and keeping area dry.
Overview of pump application, quality, and emphasis on reading safety instructions carefully.
Step-by-step guide for qualified electricians to change the pump's voltage setting.
Lists all materials required for pipe connections, well setups, and tank integration.
Guidelines for properly joining PVC and metal pipe fittings using appropriate methods.
Details requirements for suction and pressure pipes, including valves.
Crucial safety steps before installation, including power shut-off and pressure relief.
A step-by-step guide for replacing an existing pump, covering plumbing and wiring.
Identification and specifications for various plugs on the pump.
Information on shallow well installations, suitable for depths up to 25 ft.
Detailed steps for installing the pump in drilled wells using a foot valve.
Guidance on installing the pump in a suitable location and adding a pressure gauge.
Detailed steps for installing the pump in driven wells using a well point and check valve.
Instructions for connecting the male galvanized adapter to the pump suction inlet.
Advises on installing a low pressure cut-off switch for well point installations.
Visual representations of various shallow well pump installation configurations.
Recommends using pre-charged diaphragm tanks for optimal system performance.
Explains the necessity of an air volume control for non-diaphragm tanks.
Guidance on checking and adjusting the tank pre-charge pressure for pump operation.
A table detailing friction loss in plastic pipes based on flow rate and pipe diameter.
Reiterates electrical precautions and safety guidelines to prevent electric shock.
Instructions for connecting electrical service to the pump, including voltage settings.
Recommended wire gauge based on motor HP, voltage, and wire length.
Critical warning against running the pump without priming to prevent damage.
Step-by-step procedure for priming the pump when using an inline check valve.
Step-by-step procedure for priming the pump when using a foot valve.
Safety during maintenance and routine monthly checks for pump integrity.
Procedure for draining the pump and tank to prevent freezing damage.
Instructions for disassembling and reassembling the pump to replace the mechanical seal.
Possible causes and solutions for the motor failing to start.
Identifies reasons why the pump might not deliver water or deliver it at a reduced rate.
Explains why the pump might lose its prime, such as air leaks.
Addresses issues causing the pump to cycle on and off too frequently.
Details the terms, conditions, and exclusions of the product warranty.
Clarifies that the Brand is not liable for field labor or other associated costs.
Outlines general terms and specific conditions that will void the warranty.
Disclaimer on oral statements, user liability assumption, and warranty limitations.
General| Thermal Protection | Yes |
|---|---|
| Voltage | 115/230V |
| Housing Material | Cast Iron |
| Frequency | 60 Hz |
| Horsepower | 0.5 HP | 0.75 HP | 1 HP |
| Port Size | 1-1/4 in. NPT Intake, 1 in. NPT Discharge |
| Inlet/Outlet Size | 1-1/4 in. NPT Intake, 1 in. NPT Discharge |
To Next Page