What to do if my Regal boat's gauge reads erratic?
If a gauge on your Regal boat reads erratically, it could be due to a loose ground or hot wire. Repair or replace the wire and/or connection.
What to do if there is no AC power on my Regal 42SC?
If your Regal boat has no AC power, there are several potential causes: * The main shore power breakers might be tripped or in the “off” position. In this case, energize the shore power inlet breakers. * The dock power could be off, so activate dockside power. * The shore power cord may not be connected; ensure it is plugged in and twisted to lock. * There may be a faulty connection that needs repair. * For earlier yachts, a triple breaker at the output of the isolation transformer may have tripped; reset the breakers after repair. * For later yachts, the ELCI breaker might have tripped; reset the breaker after repair.
What to do if water does not enter the bowl during flush or water add cycle on my Regal boat?
If water does not enter the bowl during flush or water add cycle on your Regal boat, check the following: * The water supply line is kinked or not connected. Ensure the supply line is properly connected to the fresh water supply and check for kinks. * There is no power to the water pump. Check that the circuit breaker has not tripped and inspect all pump electrical connectors. * The water supply has been turned off. Check the water supply valve at the manifold.
Why does my Regal 42SC's fresh water pump cycle on and off?
If the fresh water pump on your Regal boat cycles on and off, it is likely due to a water system leak. Locate and repair the water leak.
What to do if my Regal 42SC's 12 volt equipment is not working?
If the 12 volt equipment on your Regal boat is not working, consider the following: * The equipment switch is in the “off” position. Switch it to the “on” position. * A circuit breaker or fuse has blown. Reset the breaker or replace the fuse. * The battery is weak or dead. Replace the battery. * There is a corroded connection. Eliminate the corrosion. * There is a loose wire. Tighten the connection. * There is an internal equipment short. Replace the equipment component.
What causes poor performance in my Regal 42SC?
Poor performance in your Regal boat may be due to: * Incorrect trim. Adjust the trim. * An unbalanced load. Adjust the load.
Why is my Regal boat's toilet not flushing or has poor flush performance?
If your Regal boat's toilet is not flushing or the flush performance is poor, here are some things to check: * The waste tank is full (the tank indicator light on the wall switch is RED). Empty the waste tank before continuing to use the toilet. Note that overriding the full tank lock-out may cause the waste tank to overflow. * There is a clog at the pump inlet. Clear the clog. * There may be low voltage. Check for no more than a 10% decrease in voltage when the macerator is running; if the voltage decreases more than this, there may be a wiring problem.
What to do if my Regal 42SC's battery is not charging while the engine is running?
If your Regal boat's battery isn't charging while the engine is running, consider these potential causes: * A loose belt. Tighten the belt. * A faulty alternator. Repair or replace the alternator. * A faulty voltmeter. Replace the voltmeter.
What causes excessive vibration in a Regal boat?
Excessive vibration in your Regal boat can stem from several issues: * Material obstructing the propeller. Try reversing the engines to remove the material. * A bent drive propeller shaft. * A bent propeller blade. In this case, repair or replace the propeller. * A noisy drive bearing. The drive unit needs repair. * A damaged drive casting. The damaged casting needs to be replaced.
What to do if there is no power to AC outlets and/or equipment on my Regal boat?
If there is no power to AC outlets and/or equipment on your Regal boat, here's what you should check: * The main AC ship’s panel breakers may be tripped or in the “off” position. Reset or activate the main breakers. * The shore power cord may not be connected. Plug in the shore power cord. * The GFCI might have tripped. Find the cause of the trip and then reset the GFCI.
To Next Page
General
