To Next PageTo Next PageWhat to do if my Rescomf XD100 Steriliser doesn't work after charging?
If your Rescomf Steriliser isn't working after charging, it could be due to an incorrect charger connection or a broken USB cable. First, check if the charger connection is correct. If it is, try replacing the USB cable with a new one. If the issue persists, it may require professional attention.
Why is my Rescomf Steriliser charging light not illuminating?
If the charging light on your Rescomf Steriliser isn't illuminating, it could be due to insufficient charging or a poor charger connection. Ensure the power outlet has electricity and that the charger is properly plugged in. Inspect the charger and USB connection. If necessary, try a new charger and USB cable.
How to fix a Rescomf XD100 that does not work after turning on?
If your Rescomf Steriliser doesn't work after you turn it on, the most likely cause is that the product is out of power. To resolve this, connect the product to a charger and plug the charger into a power outlet. Wait for the product to fully charge before attempting to use it again.
What to do if Rescomf XD100 has no sound and stops?
If your Rescomf Steriliser stops and produces no sound, the battery is likely depleted. Connect the device to a power source to charge it. This should resolve the issue.
What to do if Rescomf XD100 Steriliser does not stop automatically after 35 minutes?
If your Rescomf Steriliser doesn't stop automatically after 35 minutes, it may indicate a system failure. Try powering down the machine by pressing and holding the On/Off button for 3 seconds, and then try the cycle again.
Advises users on cleaning, disinfecting the device, and lists important cleaning precautions.
Lists the XD100 device, charger, USB cable, and user manual as part of the package.
Emphasizes using the correct charger and USB cable for charging specifications.
Identifies charging/working indicators, On/Off button, tubing port, and air inlet.
Details device dimensions, weight, battery, power, and operating conditions.
Illustrates how the device connects to a CPAP mask and tubing.
Declares compliance with CISPR 11 standards for electromagnetic emissions.
Declares compliance with IEC 61000 standards for electromagnetic immunity.
Details immunity test levels for electrostatic, transient, surge, and power variations.
Describes suitable flooring, humidity, and mains power quality for operation.
Provides guidance on conducted RF emissions and recommended separation distances.
Provides guidance on radiated RF emissions and field strength requirements.
Pre-operation checks include cleaning accessories and using an airtight container.
Explains how to turn on the device, the ozone cycle, and auto power-off.
Details how to charge the device using the USB cable and notes the charging indicator.
Explains low battery warning indicators and recommends charging promptly.
Explains symbols for temperature limits, IP rating, EC representative, and WEEE.
Advises waiting for ozone dissipation, warns about ozone exposure, and mentions battery travel suitability.
Warns against stacking the product with other devices and using non-compliant accessories.
States compliance with IEC60601-1-2 and advises using provided EMC information.
Solutions for device not turning on, charging light issues, or not working after charging.
Solutions for machine stopping, no ozone, or cycle not completing.
Fields for customer name, address, serial number, distributor, and repair date.
Instructions to retain the warranty card and sales receipt for service.
The RESCOMF XD100 Ventilation Disinfector is a device designed for the sanitization of CPAP accessories, such as masks and tubing. It utilizes controlled ozone to kill 99.9% of germs and bacteria, including Escherichia coli (8099), Staphylococcus aureus (ATCC 6538), and Candida albicans (ATCC 10231). The sanitization process is entirely dry, requiring no water, soap, or chemical cleaning.
The device operates on a 35-minute sanitization cycle. This cycle includes 30 minutes of ozone streaming, followed by 5 minutes of fresh air circulation to remove residual ozone. The manufacturer states that repeating the cycle is not necessary. To initiate the process, the user presses and holds the On/Off button for 3 seconds. A single beep and a green light indicate that ozone streaming has begun. After the 35-minute cycle, the device automatically powers off, signaled by five beeps and the green light turning off. Users are advised to wait at least an hour after the cycle before using their CPAP/Bi-Level accessories to allow any remaining ozone odor to dissipate. The device can be manually turned off during the sanitization process by pressing and holding the On/Off button for 3 seconds, which will result in a long beep and the green light turning off.
For optimal disinfection, it is recommended to place CPAP/BiPAP accessories and the RESCOMF Ventilation Disinfector inside an airtight container with dimensions equal to or smaller than 350x220x140mm (13.78” x 8.66” x 5.57”). Before sanitization, any visible residue on the CPAP/BiPAP mask or nasal pillow should be wiped clean with a cleansing wipe or damp cloth, and accessories should be disconnected from the CPAP/BiPAP machine.
The device is designed for ease of use with a single On/Off button and clear indicator lights for charging and operation. It offers a "care-free" sanitization process without the need for water or chemicals. The compact and lightweight design makes it portable. The 2000mAh rechargeable battery is equivalent to a mobile phone battery, making it acceptable for travel on most airlines.
The XD100 Ventilation Disinfector complies with IEC60601-1-2 standards for electromagnetic compatibility. It is intended for use in typical commercial or hospital environments and domestic settings. Users should ensure it is used in such environments and be aware that portable and mobile RF communication devices may affect its performance. It is advised to avoid strong electromagnetic interference from sources like mobile phones and microwave ovens when using the disinfector. The product should not be placed close to or stacked with other devices unless normal operation can be verified in such a configuration.
General| Brand | Rescomf |
|---|---|
| Model | XD100 |
| Category | Steriliser |
| Language | English |
