By
pressing
MUTING OFF
[17],
thrs function can
be defeated.
i.e.
the
potentiometer
is bypassed
(the
MUTING OFF
function
can
also be
program
assigned
to the
individual station
selector
keys). Noise can also
occur
with
stereo
reception.
lf the
noise
level
is
too
high, the
reception can only be
improved by
switch-
ing to mono
mode. The threshold
for automatic
switching
to
mono
mode is adjustable
with theTHRESHOLD
STEREO
poten-
tiometer
l27l
as follows:
-
Tune to a
weak stereo station
on
which the
noise. in
your
opin-
ion. is still tolerable.
-
TuTnTHRESHOLD STEREO
potentiometerl2Tl
clockwise un-
tilthe tuner switches to
mono reception
(the
word
STEREO
in
the display
window
[31]
disappears).
-
Take
back
potentiometer
setting until the station
is again
re-
ceived
in
stereo
mode. lt is recommended,
however, to turn
the
potentiometer
a
little further in order to
prevent
the tuner
from switching constantly between
stereo and
mono
mode
on account
of fluctuating signal strength.
2.2
DIRECT indicator
[11]
The DIRECT LED
n1l
indicates various conditions.
When the
tuner
is
switched
off but still
connected
to the
AC
power
socket,
this
LED is on
(STAND
BY mode).
When the tuner
is
switched
on, this LED lights up as soon
as
the
tuner is operated either
in automatic
or
manual tuning
mode
to
alert the
operator
to the fact that the tuned station
is not stored.
When the
tuner is
operated from a REVOX 8201 system
remote
control, this LED flashes as
soon
as
one
of the command but-
tons
is
pressed.
ln this case
the
LED
acknowledges
that a com-
mand has been received.
2.3
Receiving mode controls
[13]
through
[17]
2.3.1
MONO ON
t14l
When this button
is
pressed,
the tuner switches to
MONO
re-
ception.
lf
STEREO
ONLY
[16]
is also
pressed,
the tuner
contin-
ues to operate
in mono mode. however
only
stereo stations
are
accepted. The MONO ON
function
can be
program
assigned
to
the
individual
station selector
keys.
I17l n61
t15l
I14l
tr3l
2.3.2
HIGH BLEND
SEPARATTON
I15l
Residual noise
on stereo stations
(insufficient
signal strength)
can
be eliminated by
pressing
this button. Thisfunction narrows
the stereo base width for high frequencies.
lf the noise level is
still too
high,
switch the tuner to mono mode.
The HIGH
BLEND
SEPARATION
function can also be
program
assigned
to the individual station selector
keys.
2.3.3 STEREO ONLY
n6l
When the
button
is
pressed.
all
mono
stations rejected
in
auto-
matic
and manualtuning. lf MONO
ON
[14]
is
also
pressed.
only
stereo stations are accepted. however
the signals are
repro-
duced
on mono mode.
This function
can also
be
program
assigned
to the
individual sta-
tion selector
keys.
2.3.4
MUTTNG OFF
n7I
When
this
button is
pressed (muting
defeated,
antenna
noise
audible),
weak
stations
can be
received without changing
the
setting of the THRESHOLD
STATION
potentiometer
[25]
lf a
very weak station
(normally
rejected
by
the muting function)
is
to be
programmed
for reception
on one of the station
selector
keys. the
N/UTING
OFF
function can also be stored
in memory.
11
To Next Page
Loading...
Need help?
General
