REXON M2507R - Parts Information; Parts List for Schematic A

34 35
34 35
10 IN. (254 MM) MiterMate
TM
COMPOUND MITER SAW
When servicing use only REXON replacement parts. Use of any other parts
many create a HAZARD or cause product damage. Any attempt to repair
or replace electrical parts on this Miter Saw may create a HAZARD unless
repair is done by a qualified service technician. Repair service is available
at your nearest Service Center.
PARTS LIST FOR SAW SCHEMATIC A
WARNING
!
PARTS LIST
I.D. Description Size Q’ty I.D. Description Size Q’ty
0831 SHAFT SLEEVE 1 25Q0 WARNING LABEL 1
083Y COMPRESSION SPRING 1 2CA8
CR. RE. TRUSS HD. ROUND NECK SCREW
M6*1.0-12 1
083Z CORD CLAMP 1 2E35 TRIGGER 1
0CES COMPRESSION SPRING 1 2E7D
CR. RE. PAN HD. ROUND NECK SCREW
M6*1.0-9 1
0D87 TORSION SPRING 1 2FGW CONTROLLER ASS’Y 1
0D9B ANCHOR BLOCK 1 2FJF LEAD WIRE ASS’Y 1
0DHT SPRING GUARD WD=φ1.3 1 2T9B ROCK SWITCH ASS’Y 1
0DTZ ARBOR COLLAR 2 2V8U PC-GUARD ASS’Y 1
0DVJ BLADE WRENCH 1 2VFP ARM 1
0F1H COLLAR 1 2VFQ LASER SET 1
0J4C FLAT WASHER φ4*8-1 1 2VFR CABLE SHIELD 1
0J4E FLAT WASHER φ6*13-1 1 2VGB BRACKET 1
0JB0 WAVE WASHER WW-8 1 2VGS AXLE SEAT 2
0JVY HEX. SOC. HD. CAP BOLT M6*1.0-16 1 2VGU LASER PLUNGER HOUSING 1
0JZD HEX. SOC. SET SCREW M5*0.8-10 2 2VGW PIN 1
0JZN ARBOR BOLT M8*1.25-20 1 2VKG BRACKET 1
0K5C CR. RE. COUNT HD. SCREW M6*1.0-16 1 2VRT CUTTER SHAFT GUARD 1
0K74 CR. RE. TRUSS HD. SCREW M6*1.0-8 1 2VSN BUMPER 1
0K7Z
CR. RE. TRUSS HD. ROUND NECK SCREW
M6*1.0-14 1 2WG8 LEVER 1
0KA0 CR. RE. PAN HD. TAPPING SCREW M5*12-20 2 2WGD COLLAR 1
0KA4 CR. RE. PAN HD. TAPPING SCREW M4*16-16 2 2X5H LASER ASS’Y 1
0KA9 CR. RE. PAN HD. TAPPING SCREW M3*24-10 1 2X6M LABEL 1
0KB7 CR. RE. PAN HD. TAPPING SCREW M4*18-16 2 2ZH1 LEAD WIRE ASS’Y 1
0KB7 CR. RE. PAN HD. TAPPING SCREW M4*18-16 2 30V3 BAG-DUST ASS’Y 1
0KB8 CR. RE. PAN HD. TAPPING SCREW M4*18-20 4 36ZS BUTTON SWITCH 1
0KD8 CR. RE. PAN HD. SCREW M4*0.7-12 3 370K SEGMENT HANDLE 1
0KDH CR. RE. PAN HD. SCREW M5*0.8-8 3 37E0 BLADE 1
0KE0 CR. RE. PAN HD. SCREW M6*1.0-40 2 398Y PLUNGER HANDLE 1
0KQG CROWN NUT M4*0.7 T=6.5 1 39AA ANGLE FINDER 1
0KQX NUT M6*1.0 T=6 1 3CLW INSTRUCTIONS MANUAL 1
0KR3 LOCK NUT M6*1.0 T=6 1 3CW7 TRADE-MARK LABEL 1
0LN4 WIRE CONNECTOR 1 3CW8 TRADE-MARK LABEL 1
0LU3 LIMIT SWITCH 1 3CW9 LABEL 1
0U76 LASER STICKER 1 3CWA CAUTION LABEL 1
0XQ8 CR. RE. PAN HD. TAPPING SCREW M6*1.0-20 2 3DNE POWER CABLE 1
21GM FLAT WASHER ψ4*10-1 3 3DV6 MOTOR HANDLE 1
22XF CR. RE. PAN HD. TAPPING SCREW M3*20-15 1 3DV9 MOTOR HANDLE 1
23NX GUARD-CORD 1 3DVK MOTOR ASS’Y 1
250Z HEX. SOC. HD. CAP SCREW M5*0.8-35 3