To Next PageTo Next Page
Need help?Do you have a question about the Rheem AdvantagePlus HE80-199N and is the answer not in the manual?
General| Model Number | HE80-199N |
|---|---|
| Brand | Rheem |
| Type | Tank |
| Fuel Type | Natural Gas |
| Capacity | 80 gallons |
| Energy Factor | 0.67 |
| Voltage | 120 V |
| Warranty | 6 years |
Explains the importance of safety symbols used in the manual.
States the heater is for commercial use and requires qualified personnel for installation.
Warns about fire, explosion, property damage, injury, or death from improper use or installation.
Provides vital safety advice regarding flammable materials and gas leaks.
Step-by-step instructions in case of a gas leak detection.
Details water recovery rates in GPH and LPH at various temperature rises.
Provides recovery data for booster models at different temperature rises.
Shows total water delivery in gallons and liters for various time intervals.
Presents physical dimensions in English and Metric units, including connection details.
Warns against storing or using flammable materials near the water heater due to explosion risk.
Highlights dangers from improper venting and lack of air supply.
Details precautions for LP gas, including leak detection and emergency procedures.
Warns about severe burns from water temperatures over 125°F and related safety advice.
Emphasizes reading manual sections on Venting and Operation before installation.
Mandates installation compliance with local codes, utility requirements, and national standards.
Guides on choosing a location considering piping, venting, access, and damage prevention.
Details requirements for T&P relief valve and expansion tank.
Specifies requirements for domestic water and gas connections, including materials.
Details electrical requirements, wiring, grounding, and safety precautions.
Outlines gas supply requirements, piping, pressure, and leak testing.
Provides instructions for using 3" PVC, ABS, or CPVC for venting, including length and slope.
Lists specific rules for vent termination location and clearances.
Specifies materials for 2" venting, including ABS, CPVC, and PVC pipes and fittings.
Explains using larger pipes for longer runs and required transition fittings.
Provides critical combustion analysis readings for natural gas and propane setup.
Describes the electronic control system, its components, and diagnostic features.
Step-by-step instructions for safely starting the water heater after installation.
Explains how to set and adjust the water temperature and thermostat differential.
Outlines the normal sequence of events during the water heater's operation.
Notes that the control system requires no periodic maintenance under normal conditions.
Provides instructions for safely shutting down and preparing the heater for vacation.
Explains burner ignition failures, lockout conditions, and fuel conversion.
Addresses corrosive atmospheres and condensate removal system management.
Provides a labeled diagram identifying major components and replacement parts.
Details adjustments for ignition issues like no ignition or poor ignition.
Explains how the control system's diagnostics and LEDs aid in pinpointing problems.
Describes LED indicators for various operational states like idle, call for heat, and blower active.
Details LED indicators for pre-purge, ignition, heating, and post-purge cycles.
Addresses issues related to lack of voltage, ignitor lockout, and gas valve ignition failures.
Covers ECO switch, control health, combustion air, and temperature probe faults.
Provides a wiring diagram showing connections for the control system components.
Illustrates and lists the identification of various parts related to the control system.
Illustrates side venting configurations for different pipe sizes and setups.
Shows vertical roof venting and side wall venting with V1000 kit configurations.
Illustrates a typical setup for the AdvantagePlus with a storage tank and reverse manifold.
Details the initial actions and system checks upon applying power.
Describes the process when the thermostat calls for heat, including pre-purge, ignition, and heating.
Details the post-purge cycle and the return to an idle state after heating.
Explains the meaning of various LED states, their functions, causes, and remedies.
Lists common water heater problems and their potential causes and service solutions.
Provides contact information and necessary details for requesting service from the manufacturer.
Lists common issues related to venting and gas supply systems.
Highlights common problems with electrical, plumbing, and condensate systems.
Covers burner, gas valve concerns, and NSF sealing requirements.
