To Next PageTo Next PageWhy does my Ricoh Aficio SP 4310N say the toner has run out?
If your Ricoh Printer displays a message indicating that the toner has run out, this means the toner has run out. You should prepare a new print cartridge.
What to do if my Ricoh Aficio SP 4310N Printer shows error messages on the control panel due to paper jam?
If error messages appear on the Ricoh Printer's control panel due to a paper jam, here are some things to try: * Remove the jammed paper in the source tray, and then load the paper again. To reset the error, open the front cover and then close it. * Open the paper exit cover and remove jammed paper. * Open the rear cover and remove the jammed paper inside the fusing unit. * Detach the duplex unit and remove the jammed paper inside the duplex unit.
What to do if my Ricoh Aficio SP 4310N Printer cannot detect the Wireless LAN board?
If the Ricoh Printer cannot detect a Wireless LAN board, check if it is installed properly.
What to do if my Ricoh Printer displays an error that the print cartridge may not be installed correctly?
If your Ricoh Printer displays a message indicating that the print cartridge may not be installed correctly, turn the printer off and re-install the print cartridge.
Why does my Ricoh Aficio SP 4310N say the toner is almost depleted?
If your Ricoh Printer displays a message indicating that the toner is almost depleted, contact your sales or service representative to obtain a new print cartridge.
Why does my Ricoh Printer say some parts inside the print cartridge have reached their end of life?
If your Ricoh Printer displays a message indicating that some parts inside the print cartridge have reached their end of life, contact your sales or service representative to obtain a new print cartridge.
What to do if my Ricoh Printer displays an error because of an incorrect proxy user name or password?
If your Ricoh Printer displays an error message indicating an incorrect proxy user name or password, check the proxy server settings, and change the user name and/or password if they are incorrect.
How to solve the issue when my Ricoh Aficio SP 4310N Printer cannot detect an optional SDRAM module?
If the Ricoh Printer cannot detect an optional SDRAM module, check if it is installed properly.
What to do if my Ricoh Aficio SP 4310N shows an error that the fusing unit may not be installed correctly?
If your Ricoh Printer displays a message indicating that the fusing unit may not be installed correctly, turn the printer off and re-install the fusing unit.
What to do if my Ricoh Aficio SP 4310N displays an error that a classification code is not specified for the print job?
If your Ricoh Printer displays a message indicating that a classification code is not specified for the print job, enter a classification code using the printer properties and print the document again.
Power| power requirements | 120V, 60Hz |
|---|---|
| maximum power consumption | 960W or less |
| energy saver power consumption | 3.9W or less |
Paper Handling| standard paper supply | 500-sheet Tray + 100-sheet Bypass Tray = 600 sheets |
|---|---|
| optional paper supply | 500-sheet Paper Feed Unit (1 or 2 may be installed) |
| maximum paper capacity | 1, 600 sheets |
Print Specifications| print resolution | 300 x 300 dpi, 600 x 600 dpi, 1200 x 600 dpi |
|---|---|
| output speed | 37 pages per minute (Letter) |
| first print speed | 6.9 seconds or less |
Memory| standard memory | 256 MB RAM |
|---|---|
| maximum memory | 512 MB RAM |
| optional hard disk drive | 80 GB |
Weight and Dimensions| main unit dimensions | 15.28" x 17.72" x 13.58" (388 mm x 450 mm x 345 mm) |
|---|---|
| main unit with duplex unit dimensions | 15.28" x 21.37" x 13.58" (388 mm x 543 mm x 345 mm) |
| main unit weight | 34.1 lb. (15.5 kg) |
| main unit with duplex unit weight | 47.3 lb. (21.4 kg) |
