EasyManua.ls Logo

RIDGID RP 350 - User Manual

RIDGID RP 350
52 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
RP 350/RP 351
Press Tools
• Français – 15
• Deutsch – 31
RP 350/RP 351 Manual

Table of Contents

Questions and Answers

  • V
    Vanessa DominguezJul 28, 2025
    What to do if the attachment is locked onto fitting of RIDGID RP 350?
    • J
      James MoodyJul 28, 2025
      If the attachment is locked onto the fitting of your RIDGID Tools, it could be because the press connection was not successfully completed, so push the pressure release button to remove the jaws from the fitting. Another reason might be that you used the wrong jaw for the tube size or material, so install the correct attachment. Also, the tool was not square to the tube, so make sure that the tool is square to the tube. Finally, the attachment press contour was not aligned with the fitting contour, so make sure the attachment press contour is aligned with the fitting contour.
  • A
    April HillAug 3, 2025
    What to do if my RIDGID RP 350 will not turn on?
    • O
      obennettAug 3, 2025
      If your RIDGID Tool won't turn on, there are a few potential reasons. First, the battery might be completely discharged or has failed, so insert a fully charged battery or recharge the battery. Another possibility is that the battery isn't properly inserted into the handle of the tool, so check to ensure it is fully inserted. Finally, the AC adapter might not be correctly inserted into the tool, so make sure to correctly insert the AC adapter into the tool.
  • G
    Gina MillsAug 9, 2025
    Why is oil leaking from my RIDGID RP 350?
    • M
      Matthew BrewerAug 9, 2025
      If oil is leaking from your RIDGID Tools, it could be due to a seal or mechanical problem, in which case you should take it in for service. It's also possible that the oil level is low, so you should check the oil level.
  • S
    Suzanne NewmanAug 15, 2025
    How to fix incomplete pressed connections with RIDGID RP 350 Tools?
    • A
      April LoweAug 15, 2025
      If the pressed connections produced by your RIDGID Tools are not complete, redo the press connection with a new fitting and a new tube.
  • E
    efowlerAug 20, 2025
    What to do if motor runs but RIDGID RP 350 will not complete a cycle?
    • S
      stevenhughesAug 21, 2025
      If the motor runs but the RIDGID Tools will not complete a cycle, take it for service, as the tool is in need of repair.

Summary

Safety Symbols and Signal Words

General Power Tool Safety Warnings

General safety guidelines for operating power tools to prevent serious injury.

Personal Safety

Personal Protective Equipment

Guidelines for using PPE like eye protection, safety shoes, and hard hats.

Power Tool Use and Care

Tool Maintenance and Handling

Battery Tool Use and Care

Battery Pack Handling

Specific Safety Information

Press Tool Safety

Critical safety instructions specific to press tool operation and attachments.

Controls Chart

Tool Status Lights

Specifications

RP 350;RP 351 Specifications

Detailed technical specifications for both RP 350 and RP 351 press tools.

Pre-Operation Inspection

Daily Tool Inspection

Daily checks before use to ensure tool safety and prevent damage.

Set-Up and Operation

Attachment Installation

Procedure for correctly removing and installing tool attachments.

Preparing Connection

Fitting Preparation

Steps for preparing connections as per fitting manufacturer's instructions.

Pressing A Fitting With Typical Scissor Jaws

Holding the Tool and Jaws

Proper technique for holding the press tool and positioning jaws for a correct press.

Normal and Control Mode Operation

Pressing A Fitting With Typical Actuator And Press Ring Set

Actuator and Ring Operation

Inspecting The Pressed Connection

Connection Testing

Maintenance Instructions

Cleaning And Lubrication

Troubleshooting

Tool Not Turning ON

FULL LIFETIME WARRANTY

Warranty Information

RIDGID RP 350 Specifications

General IconGeneral
BrandRIDGID
ModelRP 350
CategoryTools
LanguageEnglish

Related product manuals