Rigol DS2072A - Page 140

To Next Page

To Previous Page

RIGOL Chapter 5 To Trigger the Oscilloscope

5-52 MSO2000A/DS2000A User Guide

Trigger Level:

Use TRIGGER

LEVEL to modify the level. For the details, please refer to the

introduction of "

Trigger Level".

Main Page

default chapter3
- Guaranty and Declaration3
- Safety Requirement4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- Care and Cleaning16
- Environmental Considerations17
- MSO2000A/DS2000A Series Overview18
- Document Overview20
- Table of Contents23
Chapter 1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- To Adjust the Supporting Legs34
- To Connect to Power Supply34
- Turn-On Checkout35
- To Connect the Probe35
- Function Inspection37
- Probe Compensation38
- Front Panel Overview39
- Rear Panel Overview41
- Front Panel Function Overview43
- Vertical43
- Horizontal44
- Trigger45
- Clear46
- Run/Stop46
- Single46
- Auto46
- Multifunction Knob47
- Navigation Knob47
- Function Keys48
- Signal Source49
- Record49
- Print49
- Logic Analyzer50
- User Interface51
- To Use the Security Lock56
- To Use the Built-In Help System57
Chapter 2 To Set the Vertical System59
- To Enable the Analog Channel60
- Channel Coupling61
- Bandwidth Limit61
- Probe Ratio62
- Input Impedance63
- Waveform Invert63
- Vertical Scale64
- Vertical Expansion65
- Amplitude Unit65
- Channel Label65
- Delay Calibration of the Analog Channel67
Chapter 3 To Set the Horizontal System69
- Delayed Sweep70
- Time Base Mode72
- Y-T Mode72
- X-Y Mode72
- Roll Mode75
- Horizontal Scale76
- Horizontal Reference77
Chapter 4 To Set the Sample System79
- Acquisition Mode80
- Normal80
- Average80
- Peak Detect82
- High Resolution82
- Sample Mode83
- Sample Rate84
- LA Sample Rate85
- Memory Depth86
- LA Memory Depth87
- Anti-Aliasing87
Chapter 5 To Trigger the Oscilloscope89
- Trigger Source90
- Trigger Mode91
- Trigger Coupling93
- Trigger Holdoff94
- Noise Rejection95
- Trigger Type96
- Edge Trigger97
- Pulse Trigger99
- Runt Trigger102
- Windows Trigger (Option)105
- Nth Edge Trigger (Option)107
- Slope Trigger109
- Video Trigger (HDTV Option)112
- Pattern Trigger115
- Delay Trigger (Option)117
- Timeout Trigger (Option)120
- Duration Trigger (Option)122
- Setup/Hold Trigger124
- RS232 Trigger126
- I2C Trigger129
- SPI Trigger132
- USB Trigger (Option)135
- CAN Trigger (Option)137
- Trigger Output Connector141
Chapter 6 MATH and Measurements143
- Math Operation144
- Addition144
- Subtraction144
- Multiplication145
- Division145
- Fft147
- Digital Filter150
- Logic Operation152
- Advanced Operation154
- MATH Label156
- Auto Measurement157
- Quick Measurement after AUTO157
- One-Key Measurement of 29 Parameters159
- Frequency Counter Measurement165
- Measurement Setting166
- To Clear the Measurement168
- All Measurement169
- Statistic Function170
- Measurement History170
- Cursor Measurement171
- Manual Mode172
- Track Mode177
- Auto Mode180
- X-Y Mode181
Chapter 7 Digital Channel183
- To Select the Digital Channel184
- To Move the Digital Channel184
- To Turn On/Off the Digital Channel185
- Group Set186
- To Set the Waveform Display Size187
- Reorder Setting187
- To Set the Threshold187
- To Use the Digital Bus188
- To Set the Label189
- Digital Channel Delay Calibration190
Chapter 8 Protocol Decoding191
- Parallel Decoding192
- RS232 Decoding (Option)195
- I2C Decoding (Option)200
- SPI Decoding (Option)204
- CAN Decoding (Option)207
Chapter 9 Reference Waveform211
- To Enable REF Function212
- To Set the Color212
- To Select REF Source212
- To Save REF Waveform213
- To Adjust REF Waveform Display213
- To Export to Internal or External Memory213
- To Import from Internal or External Memory214
Chapter 10 Pass/Fail Test215
- To Enable Pass/Fail Test216
- To Select Source216
- Mask Range216
- To Set Test Results Output Type218
- To Save the Test Mask219
- To Load the Test Mask219
Chapter 11 Waveform Recording221
- Waveform Recording222
- Record Constant on224
- Waveform Playback226
- Waveform Analysis228
- Analysis Based on Trace232
- Analysis Based on Pass/Fail Mask233
Chapter 12 Display Control235
- To Select the Display Type236
- To Set the Persistence Time236
- To Set the Waveform Intensity238
- To Set the Screen Grid238
- To Set the Grid Brightness238
- To Set the Menu Display238
Chapter 13 Signal Source239
- Parameter Setting Method240
- To Output Basic Waveform241
- To Output Sine241
- To Output Square242
- To Output Ramp243
- To Output Pulse244
- To Output DC244
- To Output Noise245
- To Output Built-In Waveform246
- To Output Arbitrary Waveform250
- To Select Waveform252
- To Create Waveform252
- To Edit Waveform254
- Modulation257
Chapter 14 Store and Recall261
- Storage System262
- Storage Type263
- Internal Storage and Recall265
- External Storage and Recall267
- Disk Management269
- To Select File Type269
- To Create a New File or Folder270
- To Delete a File or Folder273
- To Rename a File or Folder274
- To Clear the Local Memory274
- Factory275
Chapter 15 System Function Setting283
- Remote Interface Configuration284
- LAN Setting284
- USB Device289
- GPIB Address289
- System-Related290
- Sound290
- Language290
- System Information291
- Power-Off Recall291
- System Time292
- Screen293
- Self-Calibration294
- Print Setting295
- Power Status297
- Aux Output298
- Option Management299
- Auto Setting301
Chapter 16 Remote Control303
- Remote Control Via USB304
- Remote Control Via LAN308
- Remote Control Via GPIB310
Chapter 17 Troubleshooting313
Appendix A: Accessories and Options317
Chapter 18 Appendix317
Appendix B: Warranty319
- Index321

Rigol DS2072A - Page 140

Table of Contents

Related product manuals