Name: Rigol MSO4000 series
Brand: Rigol
Rating: 4 (1 reviews)

To Next Page

To Previous Page

Chapter 5 Trigger RIGOL

MSO4000/DS4000 User’s Guide 5-27

6. Set the trigger holdoff and noise rejection

Press Setting to enter the trigger setting submenu. In this submenu:

1) Press Holdoff to adjust the holdoff time (please refer to “Trigger

Holdoff”). The range is from 100 ns to 10 s.

2) Press Noise Reject to turn the noise rejection on or off (please refer to

“

Noise Rejection”).

www.calcert.com sales@calcert.com1.800.544.2843

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols7
- Allgemeine Sicherheits Informationen8
- Sicherheits Begriffe und Symbole11
- Measurement Category12
- Ventilation Requirement13
- Working Environment14
- General Care and Cleaning16
- Environmental Considerations17
MSO4000/DS4000 Series Overview18
Document Overview20
- Table of Contents24
Chapter 1 Quick Start31
- General Inspection32
- Appearance and Dimensions33
- To Prepare the Oscilloscope for Use34
- Front Panel Overview46
- Rear Panel Overview47
- Front Panel Function Overview49
- User Interface59
- To Use the Security Lock66
- To Use the Built-In Help System67
Chapter 2 Vertical System Setting69
- To Turn the Analog Channel On/Off70
- To Adjust the Vertical Scale71
- To Adjust the Vertical Position72
- To Specify the Channel Coupling73
- To Specify the Bandwidth Limit74
- To Set the Probe75
- To Specify the Input Impedance80
- To Turn Waveform Invert On/Off81
- To Specify the Vertical Reference81
- To Specify the Amplitude Unit82
- To Set the Channel Label83
- To Set the Delay Calibration85
Chapter 3 Horizontal System Setting87
- To Adjust the Horizontal Time Base88
- To Adjust the Horizontal Position89
- To Specify the Time Base Mode90
- To Turn Delayed Sweep On/Off96
- To Specify the Horizontal Reference99
Chapter 4 Sample System Setting101
- Sample Mode102
- Sample Rate103
- LA Sample Rate105
- To Specify the Acquisition Mode106
- To Set the Memory Depth109
- To Turn Anti-Aliasing On/Off111
Chapter 5 Trigger113
- Trigger Source115
- Trigger Level/Threshold Level117
- Trigger Mode118
- Trigger Coupling120
- Trigger Holdoff121
- Noise Rejection122
- Trigger Output Connector122
- Edge Trigger123
- Pulse Trigger125
- Runt Trigger128
- Nth Edge Trigger132
- Slope Trigger135
- Video Trigger140
- Pattern Trigger143
- RS232 Trigger146
- I2C Trigger150
- SPI Trigger154
- CAN Trigger157
- Flexray Trigger162
- USB Trigger165
Chapter 6 Operations and Measurements167
- To Make Math Operation168
- To Make Auto Measurement186
- To Make Cursor Measurement203
Chapter 7 Logic Analyzer221
- To Turn the Digital Channels On/Off222
- To Arrange the Digital Channels223
  - User-Defined Arrangement223
  - Auto Arrangement224
- To Perform Grouping Setting224
- To Specify the Waveform Display Size225
- To Adjust the Threshold Level226
- To Use the Digital Bus227
- To Set the Digital Channel Label230
- To Set the Delay Calibration of the Digital Channels231
- Digital Channel Waveform and Label Colors232
Chapter 8 Protocol Decoding233
- Parallel Decoding234
- RS232 Decoding (Option)239
- I2C Decoding (Option)247
- SPI Decoding (Option)252
- CAN Decoding (Option)258
- Flexray Decoding (Option)263
Chapter 9 Reference Waveform269
- To Turn the Reference Waveform Channel On/Off270
- To Select the Current Reference Waveform Channel271
- To Set the Reference Waveform Color271
- To Select the Reference Waveform Source Channel272
- To Save and Display the Reference Waveform272
- To Adjust the Reference Waveform Display273
- To Export the Reference Waveform File273
- To Import from the Reference Waveform File274
Chapter 10 Pass/Fail Test275
- To Enable or Disable the Pass/Fail Test Function276
- To Start or Stop the Pass/Fail Test Operation276
- To Specify the Source277
- To Set the Test Mask277
  - Screen Region Mode278
  - Cursor Region Mode279
- To Turn the Test Result Display On/Off281
- To Set the Output Form of Test Failure281
- To Save the Test Mask Range283
- To Load the Test Mask Range283
Chapter 11 Waveform Recording285
- To Record Waveform Using the "Record" Mode286
- To Record Waveform Using the "Open" Mode290
  - To Play Back the Waveform Recorded291
    - Manual Playback291
    - Auto Playback292
  - To Analyze the Recorded Waveform296
    - To Set the Template (Trace Mode)297
    - To Create the Pass/Fail Test Mask (Pass/Fail Test Mode)298
Chapter 12 Display Control305
- To Specify the Display Type306
- To Set the Persistence Time307
- To Set the Waveform Brightness309
- To Specify the Screen Grid Type309
- To Set the Grid Brightness309
- To Set the Menu Display Time310
Chapter 13 Store and Recall311
- Storage System312
- Storage Type313
- To Perform Internal Storage and Recall315
- To Perform External Storage and Recall317
- Disk Management320
- Factory329
Chapter 14 System Function Setting337
- Remote Interface Configuration338
- System-Related345
Chapter 15 Remote Control359
- Remote Control Via USB360
- Remote Control Via LAN364
- Remote Control Via GPIB367
Chapter 16 Troubleshooting371
Chapter 17 Specifications375
Chapter 18 Appendix387
- Appendix A: Accessories and Options387
- Appendix B: Warranty389
Index391

Rigol MSO4000 series User Manual

Table of Contents

Other manuals for Rigol MSO4000 series

Questions and Answers:

Rigol MSO4000 series Specifications

Related product manuals

Brand	Rigol
Model	MSO4000 series
Category	Test Equipment
Language	English