Rinnai INBUILT ROYALE - ETR User Manual

INBUILT ROYALE - ETR
FLAME FIRE
Customer Operation & Installation Manual
This appliance shall be installed in accordance with:
• Manufacturers Installation Instructions
• Local Gas Fitting Regulations
• Municipal Building Codes
• Installation code AS/NZS 5601 ‘Gas Installations’
• Any other local relevant Statutory Regulation
Installation & Service must be performed by an authorised person.
This heater is NOT designed to be built directly into a combustible opening.
For combustible opening installations, a Rinnai zero clearance kit must be used
and is available from your gas appliance retailer.
INSTALLER: PLEASE LEAVE THIS MANUAL WITH THE END USER AFTER INSTALLATION
END USER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
All Rinnai gas products are
A.G.A. certified
ISO 9001 Lic 4983
SAI Global

Rinnai INBUILT ROYALE - ETR Specifications

General

Category	Indoor Fireplace
Model	INBUILT ROYALE - ETR
Brand	Rinnai
Fuel Type	Natural Gas or LPG
Ignition	Electronic Ignition
Safety Features	Overheat Protection, Flame Failure Detection

Summary

Rinnai Inbuilt Royale ETR Manual Overview

Control Panel Functions

Control Panel Layout and Buttons

Identifies buttons like Lock, Flame, Timer, Override, and display for heater operation.

Heater Operation Guide

Basic On/Off and Temperature Control

Instructions for turning the heater on/off and adjusting the room temperature setting.

Special Function Controls

Explains the use of LOCK, FLAME, AUTO OFF, and OVERRIDE functions for advanced control.

Remote Control Operation

Using the Remote for Heater Control

Details remote control functions for manual operation, temperature adjustment, and timer deactivation.

Clock and Timer Setup

Setting the Heater's Internal Clock

Step-by-step instructions for setting the correct time on the heater's display.

Programming Automatic Timers

Guide to programming the dual ON/OFF timers for scheduled heating cycles.

Timer Operation Modes

Set and Forget Operation

Explains the automatic alternation between timers for continuous heating.

Preheat Function Explained

Details the preheat feature that warms the room before the programmed start time.

Safety Precautions - Part 1

Mandatory Clearances and Airflow

Specifies required minimum clearances around the heater and importance of unobstructed airflow.

Operational Safety Restrictions

Prohibits blocking air discharge and using aerosols near the operating heater.

Safety Precautions - Part 2

Child Safety and Flammable Materials

Advises on supervising children and keeping flammable items away from the heater.

Safety Precautions - Part 3

Prohibited Actions and Guards

Lists actions to avoid, mentions the dress guard, and reiterates warnings about LPG and flammable materials.

Error Code Diagnostics

Interpreting Heater Error Messages

Provides a list of error codes, their potential causes, and recommended actions or service calls.

Troubleshooting Common Issues

Solving Operational Problems

Offers solutions for common symptoms like burner failure, gas smells, fan issues, and visual problems.

Important Installation and Usage Points

Pre-Installation Checks and Guidelines

Covers checking for damage, ventilation, combustible materials, and effects of heat on flooring.

Customer Specification Overview

Heater Model and Performance Data

Details model numbers, description, gas output, control systems, and burner types.

Installation Location Requirements

Site Selection and Clearances

Specifies mandatory clearances, ventilation, hearth requirements, and flue connection compliance.

Combustible Openings and Mantles

Information on zero clearance kits for combustible openings and mantle placement rules.

Detailed Technical Specifications

Appliance Performance and Features

Lists gas input rates, pressures, flue requirements, ignition, operation, and safety devices.

Heater Physical Dimensions

Installation Dimensional Drawings

Provides detailed diagrams with all external measurements for installation planning.

Masonry Fireplace Installation Guide

Fireplace and Chimney Condition Checks

Details requirements for checking fireplace dimensions, structural integrity, and chimney conditions.

Flexible Flue Liner Installation

Instructions for installing the mandatory Rinnai Flexible Flue Liner Kit into masonry installations.

Masonry Installation Preparation Steps

Sealing and Gas Supply Connections

Covers applying sealing strips, running the gas supply, and connecting the flexitube.

Heater Component Removal Procedures

Steps for removing glass, burners, and louvre rods to prepare the heater for installation.

Masonry Heater Installation and Testing

Final Heater Positioning and Connections

Guides on sliding the heater into place, connecting gas and flue, and securing it to the fireplace.

Gas Leak Test and References

Emphasizes performing a gas leak test and refers to log installation and commissioning sections.

Combustible Opening Installation Overview

Zero Clearance Box and Air Gap

Explains the use of the zero clearance box for combustible openings and its contact with materials.

Available Flueing Options

Illustrates available flueing options for combustible opening installations, emphasizing rigid flue use.

Combustible Opening Installation Process

Frame Construction and Zero Box Fitment

Details constructing the frame and installing the Rinnai Zero Clearance Box, including plinth and surround.

Combustible Installation Connections and Testing

Gas Supply and Rigid Flue Installation

Covers running the gas supply and installing the rigid flueing system according to instructions.

Final Assembly and Leak Testing

Includes assembling the plinth, slip socket, attaching gas supply, and performing a leak test.

Final Steps for Combustible Openings

Decorative Surround and Further References

Instructions for installing the decorative surround and references to log installation and commissioning.

Ceramic Log Set Installation Guide

Log Placement and Ember Bed Setup

Detailed steps for placing the log set and applying the ember bed material correctly.

Finalizing Log Installation and Burn-in

Covers replacing glass, retainers, and initial burn-in procedures for the logs.

Testing and Commissioning Procedures

Burner Pressure Check and Gas Safety

Steps for checking and adjusting burner pressure, including safety precautions and gas leak testing.

Customer Handover and Safety Advice

Instructions for commissioning, instructing the customer, and providing safety advice regarding guards and initial operation.

Electrical Wiring Diagram

ETR Control System Wiring

Provides a detailed wiring diagram showing electrical connections for the heater's components and control system.

Installation and Commissioning Verification

Installer Verification Checklist

A checklist for certified installers to confirm all installation and commissioning steps are completed.

Installer and Fitter Information

Section for recording installer company name, contact information, and licence details.

Rinnai Support and Contact Information

Customer Service and Technical Contacts

Provides phone numbers and email addresses for Rinnai Australia and New Zealand customer service and technical support.