Ritmo BASIC 160 V1 - Operating Instructions (Continued); Welding Between Clamps (2 nd & 3 rd)

4. OPERATING INSTRUCTIONS ﻞﻴﻐﺸﺘﻟا تﺎﻤﻴﻠﻌﺗ
4./9
ﻞﻳدﻮﻤﻟا
160 BASIC و200 BASIC
ﻲﻏﺮﺒﻟا ﻞﺧدأ
V ﻪﻄﺑر نوﺪﺑ . ﺔﻀﻓﺎﺨﻟا ﻞﺧدأR ﺎهﺰﺣ ﻖﺑﺎﻄﺘﻳ ﺚﻴﺤﺑ
ﻚﻔﻟا ﺔﺒﻠﺟ ﻊﻣ.
ﻲﻏﺮﺒﻟا ﻂﺑرا
V ﻚﻔﻟﺎﺑ ﺔﻀﻓﺎﺨﻟا ﺖﻴﺒﺜﺘﻟ.
ﺮﺧﻵا ﻚﻔﻟا ﻊﻣ ﺔﻴﻠﻤﻌﻟا رﺮآ .
تﻼﻳدﻮﻤﻟا 250 BASIC و315 BASIC و355 BASIC
ﺔﻀﻓﺎﺨﻟا فﺮﻃ ﻞﺧدأ)ﻢﻬﺴﻟا ﺮﻈﻧا (ﻰﻠﻋ ﺔﻀﻓﺎﺨﻟا ﺖﺒﺜﺗ ﺚﻴﺤﺑ ،ﻚﻔﻟا ﺰﺣ ﻞﺧا
د
رﺎﻤﺴﻤﻟاS .
حﺎﺘﻔﻤﻟا ﻰﻠﻋ ﻂﻐﺿا
P ﺔﻀﻓﺎﺨﻟا ﻂﺑرو ﻞﻣﺎﻜﻟﺎﺑ لﺎﺧدﻹﺎﺑ حﺎﻤﺴﻠﻟ . نأ ﻦﻣ ﻖﻘﺤﺗP
ﻚﻟذ ﺪﻌﺑ ،ﻲﻟوﻷا ﻪﻌﺿو ﻰﻟإ دﻮﻌﻳ .
ﺮﺧﻵا ﻚﻔﻟا ﻊﻣ ﺔﻴﻠﻤﻌﻟا رﺮآ .
160 BASIC and 200 BASIC models
Insert the V screw without fastening it. Insert the R
reduction so that its groove coincides with the jaw’s
bushing.
Fasten the V screw to lock the reduction to the jaw.
Repeat the operation with the other jaw.
250 BASIC, 315 BASIC and 355 BASIC models
Insert the reduction end (see arrow) inside the jaw’s groove, so
that the reduction lays on the S pin.
Press P key to allow complete insertion and fastening of the
reduction. Make sure that P returns to its initial position,
afterwards.
Repeat the operation with the other jaw.
P
S
R
V
V
P
S
R
V
V