Robern MT Series - User Manual

209-1090 MP and MT Cabinets 03/29/07
1
Robern
701 N. Wilson Ave.
Bristol, PA 19007
1.800.877.2376
MT/MP CABINET INSTALLATION INSTRUCTIONS
Cabfax 1090
This instruction sheet contains information on how to
install MP and MT cabinets. These cabinets are available
in a variety of different heights and depths. The cabinet
Model Number describes the attributes of the cabinet as
shown in the “Key to Cabinet Model Numbers” diagram.
When installing cabinets, follow these steps:
1. Read the “General Notes” section.
2. Read the “Determining Dimensions” and “Cabinet
Location” sections on page 2.
3. Read the specifi c instruction for how your cabinet(s)
will be mounted. The cabinets can be mounted in
the following ways:
Surface mounted (see “How to Surface Mount
Cabinets” on page 4)
Recess mounted (see “How to Recess Mount
Cabinets” on page 5)
Gang mounted (see “How to Gang Mount
Cabinets” on page 6)
4. If you have purchased an Electrical option with your
cabinet(s), read “Wiring an Electrical Option” on
page 7.
5. Read the “Adjustments & Maintenance” section on
page 8.
■
■
■
General Notes
Unpack the cabinet. Check the box thoroughly for all
hardware and loose parts as follows:
Cabinet
Shelves
“Z” Mounting Bar
Hardware Bag
Make sure that you have all the contents listed above
and in the Parts List on page 9.
WARNING: An Electrical Option cabinet contains GFCI
receptacle(s). DO NOT install this cabinet on a circuit
that powers life support equipment. DO NOT use the
GFCI receptacles in the cabinet to power life support
equipment since a trip of the GFCI would shut down the
life support equipment.
■
■
■
■
IMPORTANT: Before starting your installation, remove
the door(s) from the cabinet(s) and store them in the
cabinet box. Make sure that the edges of the door(s)
are protected. Removing the doors makes it easier to
install the cabinets.
For the doors to operate properly, the cabinets must be
installed in a square and plumb manner. Use a Square
and Level when installing cabinets.
Save these instructions for future use and reference.
An improper installation voids the warranty. Installed
cabinets cannot be returned.
If you experience any problems with your cabinet,
contact your dealer or Robern directly.
Robern • 701 N. Wilson Ave • Bristol, PA 19007
1-800-877-2376 • FAX 1-215-826-9666
Limited Warranty — One Year Term (see page 10)
NOTE: If you are installing lights with the cabinets, see
the Installation Instructions included with light kit.
MT 20 D4 F B R E
KEY TO CABINET MODEL NUMBERS
WIDTH
Options:
16 (16") [406.4 mm]
20 (20") [508 mm]
24 (24") [609.6 mm]
DEPTH
Options:
D4 (4") [101.6 mm]
D6 (6") [152.4 mm]
D8 (8")
[ 203.2 mm]
MIRROR
SHAPE
or DOOR
TYPE
Options:
A (arch)
F (flat)
MD (Metallique
TM
)
CD (Candre
TM
)
E (Cite
TM
Black)
O (Cite
TM
Oxblood)
P (Cite
TM
Parchment)
MIRROR
EDGE or
FINISH
Options:
P (plain)
B (bevel)
CR (chrome)
C (chrome)
BN (brushed nickel)
N (brushed nickel)
MG (monaco gold)
HAND
Options:
R (right)
L (left)
N (left or
right)
ELECTRICAL
HEIGHT
Options:
MT Flat
30" [762 mm] front
MT Arch
34" [863.6 mm] front
MP Flat
39 3/8" [1000.1 mm] front
MP Arch
43 3/8" [1101.7 mm] front
Options:
E (outlets,
defogger
1
)
J (outlets,
nightlight;
no defogger
2
)
L (outlets,
nightlight,
defogger
2
)
1
Defogger not available for these Door Types: MD, CD, E, O, P
2
These options not for these Door Types: MD, CD, E, O, P
NOTE: The MD,E, O, and P Door Types all include bevels.

Robern MT Series Specifications