EasyManuals Logo

Roborock Q Revo User Manual

Roborock Q Revo
41 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #10 background imageLoading...
Page #10 background image
09
1. Open the top cover and nd the WiFi
indicator.
Reset WiFi
Option 2: Search for “Mi Home” in the App
Store or Google Play or scan the QR code to
download and install the app.
Instructions for Use
C
Press and hold the button to turn on the
robot. The power indicator will turn on and
the robot will enter standby mode.
Press and hold the
button to turn o the
robot and complete the cleaning cycle.
On/O
The robot cannot be turned o when it is being
charged.
Note:
2. Press and hold the and buttons until
you hear the “Resetting WiFi” voice alert. The
reset is complete when the WiFi indicator
ashes slowly. The robot will then wait for a
connection.
Open the Roborock or Mi Home App, tap “+”
and add the device as instructed in the app.
Add Device
Notes:
The actual process may vary due to ongoing app
updates. Follow the instructions provided in the app.
Only 2.4 GHz WiFi is supported.
If the robot waits more than 30 minutes for a
connection, WiFi will be automatically disabled. If you
want to reconnect, reset the WiFi before proceeding.
If you cannot connect to the robot due to your
router conguration, a forgotten password, or any other
reason, reset the WiFi and add your robot as a new device.
Note:
Remove and open the clean water tank and
ll the tank with water. Close the lid, lock the
latch, and t the tank back in place.
C1
Filling the Water Tank
Notes:
To prevent corrosion or damage, only use the
Roborock branded oor cleaner in the water tank.
Do not add too much cleaning uid to prevent the
robot from working improperly due to slipping.
To avoid water tank deformation, do not place hot
water in the tank.
If water marks remain on the water tank, wipe them
clean before reinstallation.
Press the button to start cleaning. The
robot will plan its cleaning route according
to its scan of the room. It splits a room into
zones, rst draws out zone edges, and
then lls the zone in a zigzag pattern. In so
doing, the robot cleans all zones one by one,
eciently cleaning the house.
C2
Starting Cleaning
C2-1—Zone 1 – Cleaned
C2-2—Zone 2 – Cleaned
C2-3—Zone 3 – In Progress
C2-4—Zone 4 – Next Zone
Notes:
To allow the robot to automatically vacuum and return
to the dock, start the robot from the dock. Do not
move the dock during cleaning.
Cleaning cannot start if the battery level is too low.
Allow the robot to charge before starting the cleanup.
If cleaning is completed in less than 10 minutes, the
area will be cleaned twice.
If the battery runs low during the cleaning cycle,
the robot will automatically return to the dock. After
charging, the robot will resume where it left o.
The robot will retract mop cloth mount when cleaning
the carpet. You can also set the carpet as a no-go
zone in the app to avoid it.
Before starting each mopping task, make sure that the
mop cloths have been properly installed.
Spot Cleaning
Press and hold the button to start spot
cleaning in pause mode.
Cleaning range: The robot cleans a 1.5 m
(4.9 ft) x 1.5 m (4.9 ft) square area centered
on itself.
After spot cleaning, the robot will automatically
return to the starting point and enter Standby mode.
Note:
Pause
When the robot is running, press any button
to pause it, press the
button to resume
cleaning, press the
button to send it back
to the dock.
Placing a paused robot on the dock manually will
end the current cleanup.
Note:

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Roborock Q Revo and is the answer not in the manual?

Roborock Q Revo Specifications

General IconGeneral
Wi-FiYes
Noise level- dB
Brush materialRubber
Frequency band2.4 GHz
Navigation typeLaser Distance Sensor (LDS)
Wi-Fi standards802.11b, 802.11g, Wi-Fi 4 (802.11n)
Water tank capacity0.08 L
Dust capacity (total)0.35 L
Base station functionsCharging
Vacuum cleaner programsAround/along obstacles
Battery life400 m²
Charging time4 h
Battery voltage20 V
Battery capacity5200 mAh
Package typeBox
Package depth412 mm
Package width627 mm
Package height423 mm
Package weight15300 g
ShapeRound
Product colorWhite
Dust container type-
Suction power5500 Pa
Weight and Dimensions IconWeight and Dimensions
Depth96.5 mm
Width350 mm
Height353 mm
Weight3800 g
Base station weight8600 g
Base station dimensions (W x D x H)340 x 487 x 561 mm

Related product manuals