Roborock S8 MaxV Ultra User Manual

15
Use a soft, dry cloth to wipe the charging
contacts on the robot and the dock.
*
Clean as required.
Charging Contacts
%
To move the dock, grip the cord storage slot
on the back with one hand and the inner
side of the front board with the other hand.
Do not lift the base directly to prevent the
dock from falling off.
Moving the Dock
%
Open the dirty water tank lid and pour out
the dirty water. Fill the tank with clean water,
close the lid, lock it, and shake. Pour out the
dirty water. Lock the lid and reinstall the tank.
Notes:
Ŏ
To avoid deformation, only use cold water.
Ŏ
If any water stains remain on the outside of the
water tank, wipe them with a soft, dry cloth before
reinstalling the tank.
Ŏ
The lid of dirty water tank is non-detachable.
*
Clean as required.
Dirty Water Tank
%
Lift the high-speed maintenance brush
latch and remove the brush. Remove
any entangled objects in the high-speed
maintenance brush and rinse it clean.
Reinstall the brush and latch it in place.
*
Clean as required and replace every 6-12 months.
High-Speed Maintenance Brush
%
Pull out the filter. Press the latch on the side
of the filter to flip it downwards open. Rinse
it with water, use a soft, dry cloth to wipe the
cleaning tank, and then reinstall the filter by
locking the latch. Press down the filter until
you hear it lock with a click.
*
Clean as required.
Water Filter
%
Reinstall the cleaning tank.D15-3—
The robot is equipped with a built-in high-
performance lithium-ion rechargeable
battery pack. To maintain battery
performance, keep the robot charged
during normal use.
Battery
%
Remove the cleaning tank.D15-1—
Rinse the cleaning tank with water.D15-2—
Cleaning Tank of Edgewise
Mopping Module
%
*
Clean as required.
*
Replace regularly or when it is full.
Replacing the Disposable
Dust Bag
%
Remove the dust container cover.D16-1—
Remove the dust bag and discard it.D16-2—
Notes:
Ŏ
The dust bag handle seals the bag on removal to
prevent leakage.
Ŏ
Always install a dust bag before putting back the dust
container cover to avoid auto-emptying without the
bag. You can also disable auto-emptying in the app.
Make sure the disposable dust bag is properly
installed to avoid waste escaping and damaging the dock.
Note:
Clean the filter with a dry cloth,
insert a new disposable dust bag
into the slot, and spread it evenly to
ensure it is installed in place.
D16-3—
Install the dust container cover
in place to make sure the dust
container is securely sealed.
D16-4—
Note: To prevent the dust container cover from falling
and hitting the robot, remove the cover with both
hands, one on each side.
If the robot will be left unused for a long period,
turn it off and charge it at least every three months to
avoid battery damage caused by overdischarge.
Note:

Roborock S8 MaxV Ultra Specifications

General

Package type	Box
Package depth	479 mm
Package width	494 mm
Package height	428 mm
Package weight	17400 g
Product color	White
Remotely operated	Yes
Dust container type	Combi
Brush type	Roller brush & Side brush
Noise level	67 dB
Frequency band	2.4 GHz
Navigation type	LiDAR
Integrated sensors	Camera
Water tank capacity	0.1 L
Dust capacity (base)	2.5 L
Dust capacity (total)	2.77 L
HEPA filtration system	-
Floor surfaces supported	Carpet, Hard floor
Threshold climbing (max)	20 mm
Dust capacity (vacuum cleaner)	0.27 L
Battery life	300 m²
Charging time	4 h
Battery capacity	5200 mAh
Power consumption (typical)	60 W
Suction power	10000 Pa

Weight and Dimensions

Depth	353 mm
Width	350 mm
Height	103 mm
Base station dimensions (W x D x H)	409 x 419 x 300 mm