roco 10738 - Präfix07

A
Piease note the install(ltion
decoder interface(" r
~
d with all ROCO locomotives having
We recommend, in addition to tlw c, pP ci fic l ocom otrv<' mstallation instructions, the following
procedure :
1. Remave housing and dctacll tlw rPver sing modul <' or thc already installed decoder from th
interface.
2. Insert the decod er plug into llw lllt<'rlcJ ce (Fi g. 1) so tllrtt c,icle of the decoder plug with red/orange
wire at the side of the intrrf,lu' ITlcllked with + or + (polc1rity according to NMRA/NEM rules, i. e.
the locomotive mov es with tlw driwr 'c, cab n o.1 f clCinq lorward).
3. lnstall the decoder in a sui t ai> IP locc~lron wi th in tlw locomotive. No part of the decoder must b
tauehing metal part s of the l ocornotrve ! lf neces smy the location of the decoder must be
insulated with insulation tape to prot ec t the decod er. The insulation must be attached to
the metal parts of the locomotiv e, b ut N OT to the dccoder (e.g. by winding the insul a tion
tape around the decod er!). 1 hic, could I ead to failur <' olthe decoder due to overheating. Da mag
claims caused by such failurps Cdnnot be ac ceptctl
The factory used h eat shnnk tui>IIHJ drou nd t he dr mciPr ensures a sufficien t heat dissip ation and
should not be remov ed.
4. lf necessary the decoder can Iw wcurPd in the de s~r<'d locc~tion with double-sided tape.
Operational test
lf the locomotive lights do not opercl l <', tlw eir eod er w as inc,Ntccl incorrectly into the interface . Reinscrl
decoder turned by 180 ° in the interfclCP .
locomotive address
The factory-set default Motorol a lt • aclclr<"' " of the de codN ic, 03 .
Operation on analog layou
A ROCO locomotive equipped with c1 drcodrr ca n also I H' run on a conventio nal Iayout. To changc
direction
of travel the control knob of the controll er must first be set to zero. Only tlwn trlll
the direction of travel be se l cc trd wrth ,m oh viou s and lorHJrr switching pulse. The brightn ess of tiH•
lamps depends on the speed of tiH ' tr<1111. !Iu• lr ght s can notiH' turned off and a possibly in sta ll ed c,pec rdl
function F1 will not oper atc. Rcprogrt1m ming of previously set addresses and functions is not
possible while
in analog operation.
list of supported RPqtster resp-cvs
The following Iist inform s aboul tlw pro<Jr cu nm i ng Cflp,rl>rlrtr<''> of the decoder. We recommrnd to
test your locomotive/railc ar with rl'CJdlcl to sta rting voll dCJP, ilcce l erat ion, br a king and maxrmum
speed du ring operations to ch eck rf tlww c h arac teristic c, .ttl' wt conforming to your wi sh es BEFORf
changing the factory-set dcfault wttings .
Programming lnstru\.tions : v• . Jiär klin * 6020/6021
Caution:
> The cantroll er must be sc t tu "0".
> No other locomotive except tlw o ru ' to Iw pr o gramm l'd rnt~y be on thc tracks.
> While programming pay a ttPntr on to tlw flas h ing ol tlw loc ornotiv<' hcfldlights.
> Any number of changes/adjuc,tnwnl'. nrn be madc ,,., l orHJ tl'> tlw cl!'coder is in
programming mode.