Rohde & Schwarz CMW500 Series - Page 290

Index
R&S
®
CMW500
290User Manual 1173.9463.02 ─ 02
REM .............................................................................. 119
REMOTE .......................................................................... 14
Remote channels .......................................................... 119
multiple .................................................................... 125
Remote control .............................................................. 119
interfaces and protocols .......................................... 119
introduction .............................................................. 119
multiple channels .................................................... 125
Remote Desktop .............................................................. 33
Remote settings .............................................................. 95
Remote trace ................................................................ 189
REN .............................................................................. 274
Repetition ...................................................................... 106
Repetition mode ...................................................... 63, 142
Replacing
AC Fuse Board .......................................................... 24
Fuses .................................................................. 24, 25
Reset ................................................................................ 84
Reset Values
Status Reporting System ........................................ 178
Resource and path management .................................. 159
Resource conflicts .......................................................... 162
Response (to queries) .................................................... 131
Response buffer (remote control) .................................. 182
Revision ............................................................................ 9
RF connectors .................................................................. 18
RF Loop Test ................................................................ 104
RF path settings
generators .......................................................... 58, 79
measurements .......................................................... 61
Rotary knob ...................................................................... 17
ROUTe .......................................................................... 134
RPC protocol .................................................................. 270
RPM (Resource and Path Management) ...................... 159
RSI file ............................................................................ 99
RX measurement ............................................................ 78
S
Sample Bus Test ............................................................ 104
Sample session ................................................................ 49
Save ................................................................................ 87
Save/Recall ...................................................................... 86
Save Profile (Selftest) .................................................... 106
SCPI
command structure .................................................. 127
SCPI compatibility .......................................................... 121
SCPI Status Register .................................................... 167
event status register ................................................ 171
IST flag .................................................................... 170
parallel poll enable register ...................................... 170
service request enable register .............................. 169
STATus:OPERation register .................................... 172
STATus:QUEStionable register .............................. 175
status byte .............................................................. 169
Structure .................................................................. 166
SCPI subsystems (overview) ........................................ 134
SDC .............................................................................. 275
Selection Filter (selftest) ................................................ 106
Selftest .......................................................................... 100
parameters .............................................................. 105
Selftest configuration .................................................... 106
Selftest Ctrl. (softkey) .................................................... 105
SENSOR connector ........................................................ 19
Sequential command execution .................................... 164
Serial Poll ...................................................................... 177
Service request .............................................................. 176
Service Request Enable
........................................ 166, 169
Setup ................................................................................ 93
Setup file .......................................................................... 36
Setup keys ...................................................................... 16
Shipment, check .............................................................. 21
Short form (command) .................................................. 129
Shut down ........................................................................ 31
Signaling applications ...................................................... 79
Signaling configuration (example) .................................... 52
Signaling control
remote .................................................................... 150
Signaling control (manual) .............................................. 80
Single (scalar) value ...................................................... 146
Single-shot .................................................................... 142
Socket communication .................................................. 272
Soft-front panel ................................................................ 48
Softkey ............................................................................ 15
Software structure .......................................................... 134
Software update .............................................................. 36
Software Update .............................................................. 95
SOURce ........................................................................ 134
SPD ................................................................................ 275
SPE ................................................................................ 275
SRE ........................................................................ 166, 169
SRQ .............................................................. 166, 176, 274
Standard deviation .......................................................... 67
Standby
key ............................................................................ 14
state .......................................................................... 25
Start Automatically (selftest) .......................................... 106
Startup dialog .................................................................. 83
Startup procedure ............................................................ 30
Statistical length .............................................................. 63
Statistical results .............................................................. 64
Statistical settings
remote control .......................................................... 142
Statistic count ................................................................ 142
Statistic Count .................................................................. 63
Statistics cycle ................................................................ 63
Statistics type .......................................................... 64, 143
STATus Commands ...................................................... 219
Status Registers ............................................................ 166
Status reporting system
Error queue .............................................................. 178
Parallel poll .............................................................. 177
Queries .................................................................... 177
Reset Values .......................................................... 178
Serial poll ................................................................ 177
Service request ........................................................ 176
STB ........................................................................ 166, 169
Stop condition .................................................................. 63
Stop Condition .............................................................. 106
Storing the instrument ...................................................... 27
String .............................................................................. 133
Sub-instrument ................................................................ 55
SW/HW Equipment .......................................................... 99
Syntax elements (SCPI, overview) ................................ 133
SYS SYNC .................................................................... 108
SYS SYNC IN ................................................................ 269
SYS SYNC OUT ............................................................ 269
System (Setup) ................................................................ 93
SYSTem Commands .................................................... 241
System messages .......................................................... 117
T
Task bar .......................................................................... 47