Rohde & Schwarz ZNB - Page 1495

Index
R&S
®
ZNB/ZNBT
1495User Manual 1173.9163.02 ─ 54
Shift Trace ....................................................................... 334
Show <Trace Name> ...................................................... 305
Show All Data ..................................................................312
Show All Mem ................................................................. 312
Show All Traces .............................................................. 305
Show as .......................................................................... 273
Show Cal Kit Label .......................................................... 703
Show Limit Fail Symbols ................................................. 693
Show Point List ............................................................... 403
Show/Hide data trace ...................................................... 310
Show/Hide memory trace ................................................ 310
Side lobe level
Frequency window .................................................... 320
Side Lobe Level (time gate) ............................................ 325
Single sweep ................................................................... 412
Single sweep mode
Sweeps (# of) ............................................................412
Single-ended mode ................................................. 129, 130
Skew ............................................................................... 658
Sliding Match ...................................................................165
Smart Fixture De-Embedding ..........................................232
Smarter calibration .......................................................... 181
SMARTerCal ....................................................................181
Ports ................................................. 452, 461, 467, 475
Ports, Standards and Power ..................................... 472
Power Meter ..................................... 454, 463, 467, 476
Power Port ................................................ 454, 463, 467
Power Sweep Diagram ............................................. 472
Procedure ................................................................. 415
Type .................................................................. 467, 476
SMARTerCal (Manual) Wizard
Calibration .................................................................470
SMARTerCal wizard
Cal Unit ..................................................................... 450
SMARTerCal wizard (Cal Unit, MultiCal)
Connections .............................................................. 463
Define Calibration dialog ........................................... 461
MultiCal ..................................................................... 459
Ports ......................................................................... 460
SMARTerCal wizard (Cal Unit) ........................................ 450
Abort Sweep ............................................................. 458
Apply ......................................................................... 459
Connections .............................................................. 454
Data acquisition ........................................................ 456
Ports ......................................................................... 451
Start Cal Sweep ........................................................ 458
SMARTerCal Wizard (Manual, MultiCal)
Connectors and Cal Kits ........................................... 476
Ports and Type ..........................................................474
SMARTerCal wizard (manual)
Connectors and Cal Kits ........................................... 468
Ports and Type ..........................................................465
SMARTerCal wizard (MultiCal)
Cal Unit ..................................................................... 459
Smith ............................................................................... 292
Smith chart .......................................................................111
Smoothing ....................................................................... 332
Aperture .................................................................... 333
Softtool panel
Minimize/maximize ................................................... 698
Softtools ............................................................................ 54
Software Option Info ....................................................... 714
Source
Calibration .........................................................433, 443
Source Port ..................................................................... 269
Source power calibration .................................................176
SPAN ................................................................................. 89
Span = Marker .................................................................380
Span Frequency .............................................................. 384
SPD ............................................................................... 1431
SPE ............................................................................... 1431
Split All ............................................................................ 687
Split diagrams ................................................................. 688
Dual Split .................................................................. 688
Quad Split ................................................................. 688
Triple Split ................................................................ 688
Split Type ........................................................................ 689
Src. for Rcvr. Cal ............................................................. 554
SRE ......................................................................... 764, 768
SRQ .............................................................. 764, 774, 1430
Stability (softkey) ............................................................. 286
Stability factors ................................................................ 133
Stability tab ......................................................................285
Standby and ready state ................................................... 25
Standby key ................................................................ 38, 42
START ............................................................................... 89
Start = Marker ................................................................. 380
Start Frequency ...............................................................384
Start Power ..................................................................... 386
Startup and shutdown ....................................................... 24
Status bar .......................................................................... 57
Status Bar
Show/hide ................................................................. 697
Status Registers .............................................................. 764
Status reporting system
common commands ......................................... 778, 780
Error queue ............................................................... 777
Parallel poll ............................................................... 776
Queries ..................................................................... 776
Reset Values ............................................................. 777
Serial poll .................................................................. 775
Service request ......................................................... 774
STB ......................................................................... 764, 768
Step attenuators .............................................................. 386
Step Size (dialog) .............................................................. 65
STIMULUS ........................................................................ 36
Stimulus Axis ...................................................................526
Stimulus softtool .............................................................. 383
Power tab ..................................................................385
Stimulus tab .............................................................. 383
Time Domain X-Axis tab ........................................... 387
Stimulus tab .................................................................... 383
Center Frequency ..................................................... 384
CW Frequency .......................................................... 385
Number of Points ...................................................... 384
Power ........................................................................386
Span Frequency ....................................................... 384
Start Frequency ........................................................ 384
Stop Frequency ........................................................ 384
STOP .................................................................................89
Stop = Marker ..................................................................380
Stop Frequency ............................................................... 384
Stop Power ......................................................................386
Storing ........................................................................... 1444
String .............................................................................. 754
Support ..........................................................................1423
Sweep
Sweep Params ......................................................... 392
Sweep Active Channel .................................................... 415
Sweep All Channels ........................................................ 414
Sweep Control
Restart Manager dialog ............................................ 414
Sweep Control tab ........................................................... 411
Sweep History .............................................................. 1404