Roland CAMM-1 PRO User Manual

Thank you very much for purchasing the CX-500/400/300.
• To ensure correct and safe usage with a full understanding of this product's
performance, please be sure to read through this manual completely and store
it in a safe location.
• Unauthorized copying or transferral, in whole or in part, of this manual is
prohibited.
• The contents of this operation manual and the specifications of this product
are subject to change without notice.
• The operation manual and the product have been prepared and tested as much
as possible. If you find any misprint or error, please inform us.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or
damage which may occur through use of this product, regardless of any failure
to perform on the part of this product.
• Roland DG Corp. assumes no responsibility for any direct or indirect loss or
damage which may occur with respect to any article made using this product.
All manuals and user guides at all-guides.com
all-guides.com

Roland CAMM-1 PRO Specifications

General

Model	CAMM-1 PRO
Category	Plotter
Cutting Force	350 gf
Interface	USB
Software Compatibility	Roland CutStudio
Blade Types	Roland compatible blades
Resolution	0.0004 in
Supported OS	Windows

Summary

Checking Supplied Items

Part Names and Functions

Front View

Identifies and describes the front components of the cutting machine.

Rear View

Identifies and describes the rear components of the cutting machine.

Operation Panel

Details the keys and display of the cutting machine's operation panel.

Setup

Setting Up

Provides instructions and precautions for setting up the cutting machine and its stand.

Connection

Explains how to connect the cutting machine to a computer via USB or parallel cable.

Turning on the Power

Instructs on how to turn the cutting machine's power on.

Installing and Setting Up the Driver

Guides on installing the necessary driver software from the included CD-ROM.

Basic Operation

Loading the Material (Roll Material)

Details the procedure for loading roll material onto the cutting machine.

Installing a Blade

Provides instructions and precautions for installing a blade into the cutting machine.

Adjusting the Blade Force and Cutting Speed

Explains how to perform a cutting test and adjust blade force and cutting speed.

Setting the Origin Point

Guides on how to set the starting point (origin) for cutting operations.

Starting Cutting

Details the process of starting a cutting job, including material test feed.

When Cutting is Completed

Provides instructions on safely removing material and the blade after cutting is finished.

Advanced Operation

Detailed Cutting-condition Settings

Explains how to adjust blade extension and offset for precise cutting conditions.

Details of the Origin-point Location and Cutting Area

Explains how the origin point and cutting area are determined based on material loading.

Coordinate Rotation Settings

Explains how to rotate cutting coordinates by 90 degrees for different layouts.

To Perform Lengthy Cutting

Provides instructions for performing lengthy cutting operations, including loading material.

Loading Flat Material (Standard-size Material, Cut Material, Etc.)

Guides on how to load flat materials onto the cutting machine.

Repeating the Same Cutting

Explains the "Replot" feature for creating numerous copies of the same cutting.

Front Loading

Explains how to install the sheet hanger for front loading and set the origin point.

The Overcut Feature

Explains the Overcut feature for enhancing sharp corners and angles.

The Preset Feature

Details how to store and call up custom cutting conditions using presets.

The Crop Mark Feature

Guides on setting crop marks for accurate cutting around printed graphics.

About the Blades and Materials

Blade and Material Combinations

Provides a guide to compatible blades, materials, and their recommended cutting conditions.

Descriptions of Features

Key Operations

Explains the functions of direct keys and menu mode operations, including flowcharts.

Maintenance

Cleaning

Provides detailed instructions for cleaning the cutting machine's body, platen, grit rollers, and pinch rollers.

Consumable Items

Describes consumable parts like blades, blade holders, and blade protectors that may need replacement.

How to Replace the Separating Knife

Details the procedure for safely replacing the separating knife on the machine.

If There Is a Problem

Self-test Operation Check

Guides on performing a self-test operation check to verify machine functionality.

What to do if...

Troubleshoots common issues like power, connection, setup, software, and OS.

Error Messages

Lists and explains common error messages displayed by the machine and their meanings.

Specifications

Specifications

Lists detailed technical specifications for CX-500, CX-400, and CX-300 models.

Interface Specifications

Details the parallel and USB interface specifications and connector pinouts.

Instruction Support Chart

Provides a chart indicating compatibility of various instructions for mode 1 and mode 2.