Roland D-50 - Page 117

%*4-6 Hach patch block consists of the following.
Function Value
8 Patch o-
1 Patch > 2 Oo -
2 Patch 3 o -
3 Patch 4 oo-
1 Patch & o~
5 Patch Name 6 o-
6 Paich Name 7 oO -
7 Patch Name 8 o-
8 Patch Name 9 o -
9 Patch Name 10 Oo -
10 Patch Name Jt o =
It Patch Name [2 o-
12 Patch o-
13 Patch o-
‘4 Pateh o =
15 Patch > 9 -
16 Patch Ni o-
17 Patch o-
18 Key Mode o-
19 Split Point
20 Portumento Mode
21 Hold Mode
22> Upper Tone Key Shift
23° Lower Tone Key Shift
24 Upper Tone Fine Tune
23 Lower Tone Fine Tune
26° Bender Range
27 After touch Bend Range
28 = Porlamento ‘Time
29 Output Mode
30 Reverb Type
St Reverb Balance
32 Totat Volume
33° Tone Balance
34 Chase Mode
35 Chase Level
360 Chase Time
37 MIDI ‘Transmit Channel
38 MIDI Separate Rev Channet
39° MIDI Transmit Prog. Change
AQ Extension — for future)
ai Extension
42 Extension
48 Extension
44 Extension
45 — Extension
46 Extension
47—__Extension
a8 Extension
50 Extension
51 Extension
Extension
Extension
Extension
Extension
Extension
Extension
Exiension
Extension.
SOCOSSOSCSOSOSSOSOSCOSSOOTSOE ON OOOOD OOS OSC O OSD OOD OSCOO
‘
Extension
4-7 Each reverb block (17 ~ 32) consists of the following.
9 ! 0000 aaaa | Reverb data I
| 0000 aaaa }
2 | 0000 aaaa | Reverb data 2
| 0060 aaaa |
374 =| «0000 «aaaa | Reverb data 188
| 0000 aaaa |
100
16
16
100
127
127
127
127
17
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
127
5. TRANS! EI EXCLUSIVE MESSAGES IN NORMAL MODE
S41 Data set (One way) DTI k2H
When Request Data (RQL) is recognized, the data within the range set with RQ--1
messages will be transmitted on the channel set with MEDI CH in MIDI Func,
regardlss of the transmit channel set with TxCH in Patch Func.
When any of Patch Group, Bank or Number is changed by operating the panel
of the unit and if Exclu in MIDI Func is set to P—Dump, all data in Temp, area
will be transmitted on the channel set with TxCH in Patch Func,
Byte Description
a 3111 0000 Exclusive status
b 0100 O00F Roland 1D #
¢ 9000 nnan Device 1D # = MIDI basic channct
where nonn + 1 = channel #
d 0001 0100 Modet-ID # ( D-50)
¢« 000] 010 Command-ID # (DT1)
{ Qaaa aaaa Address MSB *5-1
g Obbb bbbb Address
hh Ocee cee. Address LSB
(Whole,Dual Split, i Oddd dddd Data *S-1
Separate,Whole—S, 3
Dual—SSplit— US, j Oece ecce Checksum.
Split—LS,Separate—$) k o1bdl OLE End of System Exclusive
(C2,.C#2 — C7)
W,L,UL) Notes =
GLUL) *5-1 Transmitted several times in smaller portion than the total number 266 in
(-24 - +24) data byte of each message acrcoding to the address size assinged wilh
(-24 - +24) Request Data (RQL).
(-50 ~ +50)
(-50 — +50) 6, RECOGNIZED EXCLUSIVE MESSAGES IN NOMAL MODE
(-12 — +12) 6.1 Request Data (One way) RQL LH
(i - 4) Recognized if Exclu in the MIDI function is ON or P-Dump.
a -— 32)
Byte Description
a Ltt 0000 Exclusive status
(UL,ULL,ULU) b 0100 CODE Roland ID #
¢ 0000 nann Device—ID # = MIDI basic channel
where nonn + 1 = channel #
(Basic CH, 1 - 16) d 0001 0100 Model-ID # ( D-50)
(OFF,1 — 16) e 0001 0001 Command—ID # (RQ!)
(OFF, 1-100) f Qaaa aaaa Address MSB *6-1
g Obbb bbbb Address
h Occe ccec Address LSB
i Oddd dddd Size MSB *6-1
} Qeee eece Size
kK Off {fff Size LSB
t Ogee gees Checksum
m i121 0121 End of System Exclusive
6.2 Data set (One way) DTI 12H
Recognized if Exclu in the MIDI function is ON or P—Dump.
Byte Description
a HHL 0000 Exclusive status
b 0100 0001 Roland ID #
¢ 0000 nann Device ID # = MIDI basic channel
where nnnn + 1 = channel #
d 0001 0100 Modet-ID # ( D-50 )
e 0001 0010 Command—ID # ( DTI)
f Qaaa aaaa Address MSB *6-1
& Obbb bbbb Address
hh Ocee cece: Address LSB
i Oddd dddd Data *6-2
} Oeee cece Checksum
k AIH OM End of System Exclusive
Notes :
*6—1 Any address size can be assinged within the range of Temparea.
*6—2 Number of the data bytes should not exceed 256, (except sum)
All the 188 data (376 byte) are related each other, therefore receiving or sending
a parl of data docs not achieve anything.
11