To Next PageTo Next Page
Need help?Do you have a question about the Roland D-05 and is the answer not in the manual?
General| Equalizer | Yes |
|---|---|
| Product type | Digital synthesizer |
| Product color | Black |
| Sound effects | Chorus, Equalization, Reverberation |
| Volume control | Rotary |
| Keyboard number of keys | - |
| Maximum polyphony (notes) | 16 |
| Battery type | AA |
| Operating time | 5 h |
| Power source type | Battery |
| Number of batteries supported | 4 |
| Display type | LCD |
| Display number of lines | 2 lines |
| USB ports quantity | 1 |
Weight and Dimensions| Depth | 128 mm |
|---|---|
| Width | 300 mm |
| Height | 46 mm |
| Weight | 900 g |
Explains how to edit parameters by switching between display screens.
Details joystick functions and their role in editing parameters.
Explains how the Upper and Lower Tones are played on the keyboard.
Specifies the split point used when KEY MODE is set to SPLIT.
Adjusts the volume balance between the Upper and Lower Tones.
Allows transposition of the keyboard pitch in semitone steps.
Defines how control functions affect each patch.
Selects the Tone that adopts the Portamento effect.
Selects the Tone affected by the Pedal Hold effect.
Determines how Tones take on reverb and appear at outputs.
Enables outputting the Lower Tone slightly later than the Upper Tone.
Shifts the pitch of the Lower Tone in semi-tone steps.
Shifts the pitch of the Upper Tone in semi-tone steps.
Allows fine tuning of the Lower Tone's pitch.
Allows fine tuning of the Upper Tone's pitch.
Sets the transmit channel for each Patch.
Sets the Program Change number transmitted for each patch.
Sets the receive MIDI Channel in separate mode.
Explains how to copy reverb types between patch banks.
Details the procedure for writing and saving edited patch data.
Lists common parameters for Upper/Lower Tone menus.
Selects one of seven ways partials are combined and used.
Details the Pitch Envelope parameters like Velocity Range and Keyfollow.
Configures LFO parameters like Waveform, Rate, Delay, and Sync.
Details EQ parameters (Low/High Freq/Gain) and Chorus parameters.
Adjusts coarse and fine pitch for the waveform generator.
Configures LFO and P-ENV modes for pitch modulation.
Adjusts pulse width and its sensitivity to velocity and aftertouch.
Selects the waveform and PCM wave number for the generator.
Selects LFO for periodic pulse width modulation (PWM).
Adjusts the cutoff frequency and resonance of the TVF.
Configures TVF Envelope parameters: Depth, Velocity, Keyfollow, and Time.
Sets the levels for points 1, 2, 3, and Sustain in the TVF envelope.
Applies LFO and Aftertouch modulation to the TVF cutoff point.
Adjusts Level, Velocity Range, and Bias Point for the TVA.
Sets the time for each point in the TVA envelope.
Sets the levels for points 1, 2, 3, and Sustain in the TVA envelope.
Applies LFO and Aftertouch modulation to the TVA volume.
Explains how Key Mode affects notes in mono vs. poly mode for MIDI input.
Details sequencer operation, tempo, step input, and pattern playback.
Adjusts sequencer parameters like length, scale, start/end steps.
Explains how to access and use the arpeggiator functions.
Details how to write and edit sequencer patterns.
Specifies the tempo for sequencer patterns.
Specifies the amount of rhythm 'bounce' (shuffle).
Specifies the patch used when a pattern is played.
Explains step recording input for sequencer patterns.
Explains data transfer methods like handshake and one-way.
Details handshake transfer for reliable data verification.
Describes one-way transfer, simpler but less reliable for large data.
Explains bulk loading patches from D-50 to D-05.
Details transferring patches from D-50/550 to D-05.
Lists preset patches for P1 (Original D-50).
Lists available reverb types.
Lists preset patches for P2.
Lists preset patches for P3.
Lists preset patches for P4.
Lists preset patches for P5.
Lists preset patches for P6.
Details Oneshot and Loop waveforms.
Continues the list of Oneshot and Loop waveforms.
Lists parameters common to all screens (PATCH TOP).
Details common tone parameters like Struct and P-ENV.
Lists LFO parameters for LFO-1, LFO-2, LFO-3.
Lists Equalizer and Chorus parameters.
Lists Time Variant Amplifier parameters.
Details parameters for Form, Pitch, WG Mod, TVF.
Lists system parameters like Function, Demo, and Scale.
Explains Channel Voice Messages and Control Change messages.
Details Channel Aftertouch and Pitch Bender Change messages.
Explains All Sounds Off and Reset All Controllers messages.
Explains receiving Channel Voice Messages.
Describes Active Sensing and System Exclusive Messages.
Details MONO and POLY mode messages.
Summarizes control messages for Note, Mode, Program Change, etc.
Details one-way data transfer methods and message types.
Explains handshake data transfer for reliable data exchange.
Describes how to request data transmission from another device.
Explains the format for transmitting actual data.
Details the message for requesting data transmission.
Explains the format for transmitting actual data.
Describes the rejection message to forcibly end communication.
Explains address mapping for temporary and work areas.
Lists MIDI implementation for Partial Parameters.
Details MIDI implementation for Common Parameters.
Lists MIDI implementation for Patch Parameters.
Details MIDI implementation for the Reverb Block.
Provides Decimal and Hexadecimal conversion tables.
Summarizes MIDI functions, modes, and messages.
