Recording a Pattern
129129
Erasing Unwanted Performance Data
(ERASE)
All performance data of the specied type is erased. Since the
erased performance data is replaced by rests, the length of the
pattern does not change.
Parameter Value Explanation
TARGET
LOOP
Changes apply to the region specied
in LOOP SETTING (p. 112).
PATTERN Changes apply to the selected pattern.
<Event>
Changes apply to the selected pattern.
All All performance data
Note Note messages
Control
Change
Control change messages
Pitch Bend Pitch bend messages
Poly
Aftertouch
Polyphonic aftertouch messages
Channel
Aftertouch
Channel aftertouch messages
RANGE MIN
[E3] knob
0 (C-1) –127
(G9)
Species the lower limit of the region
that is erased.
RANGE MAX
[E4] knob
Species the upper limit of the region
that is erased.
If EVENT is set to “Note”, “Poly Aftertouch”, or “Control
Change”, you can specify the range of values. Range
Min species the minimum value of the range, and
Range Max species the maximum value of the range.
MEMO
¹ If you want to erase all notes or all polyphonic
aftertouch data, set Range Min to “C1” and Range
Max to “G9”. If you want to erase “C4”, set both Range
Min and Range Max to “C4”. If you want to erase from
“C3” through “C4”, set Range Min to “C3” and Range
Max to “C4”.
¹ If you want to erase all controller numbers, set
Range Min to “0” and Range Max to “127”.
Transposing
(TRANSPOSE)
This function transposes the notes of the specied region in a range
of ±24 semitones.
Parameter Value Explanation
TARGET
LOOP
Changes apply to the region specied
in LOOP SETTING (p. 112).
PATTERN Changes apply to the selected pattern.
BIAS [E1]
knob
-127–127
Species the amount of transposition
in semitone units.
RANGE MIN
[E3] knob
0 (C-1) –127
(G9)
Species the lower limit of the region
of notes that is transposed.
RANGE MAX
[E4] knob
Species the upper limit of the region
of notes that is transposed.
Changing the Velocity
(CHANGE VELOCITY)
This function changes the keyboard dynamics (velocity) in the
specied region.
Parameter Value Explanation
TARGET
LOOP
Changes apply to the region specied
in LOOP SETTING (p. 112).
PATTERN Changes apply to the selected pattern.
BIAS [E1]
knob
-99–99
Species the amount by which the
recorded velocity is changed.
Parameter Value Explanation
RANGE MIN
[E3] knob
0 (C-1) –127
(G9)
Species the lower limit of the region
of notes that is modied.
RANGE MAX
[E4] knob
Species the upper limit of the region
of notes that is modied.
Changing the Duration of the Notes
(CHANGE DURATION)
This function changes the duration (the time from note-on to note-
o) of the notes in the specied region. You can use this conversion
to give the performance a more staccato or tenuto feel.
Parameter Value Explanation
TARGET
LOOP
Changes apply to the region specied
in LOOP SETTING (p. 112).
PATTERN Changes apply to the selected pattern.
BIAS [E1]
knob
-960–960
Species the amount by which the
note duration is changed.
RANGE MIN
[E3] knob
0 (C-1) –127
(G9)
Species the lower limit of the region
of notes that is modied.
RANGE MAX
[E4] knob
Species the upper limit of the region
of notes that is modied.
Moving Performance Data Forward or Backward
(SHIFT CLOCK)
This function moves the timing of performance data in the specied
region forward or backward in units of ticks. By slightly moving
the performance data you can give the performance a “rushing” or
“dragging” feel.
If the Shift Clock function would cause data to be moved beyond
the beginning of the song, such data is moved to the beginning of
the song.
Parameter Value Explanation
TARGET
LOOP
Changes apply to the region specied
in LOOP SETTING (p. 112).
PATTERN Changes apply to the selected pattern.
Event
Selects the performance data that is moved.
All All performance data
Note Note messages
Control
Change
Control change messages
Pitch Bend Pitch bend messages
Poly
Aftertouch
Polyphonic aftertouch messages
Channel
Aftertouch
Channel aftertouch messages
BIAS [E1]
knob
-960–960
Species the number of ticks by which
the data is shifted.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
