Roland HandSonic HPD-20 - Page 4

MIDI Implementation
4
 Sound Controller 8 (Controller Number 77)
Status 2nd byte 3rd byte
BnH 4DH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “SOUND8 (77) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting
is “SOUND8 (77) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting
is “SOUND8 (77) ,” this message is used as Realtime Modify (EFFECT) control
information.
 Sound Controller 9 (Controller Number 78)
Status 2nd byte 3rd byte
BnH 4EH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “SOUND9 (78) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting
is “SOUND9 (78) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting
is “SOUND9 (78) ,” this message is used as Realtime Modify (EFFECT) control
information.
 Sound Controller 10 (Controller Number 79)
Status 2nd byte 3rd byte
BnH 4FH vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “SOUND10 (79) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“SOUND10 (79) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“SOUND10 (79) ,” this message is used as Realtime Modify (EFFECT) control
information.
 General Purpose Controller 5 (Controller Number 80)
Status 2nd byte 3rd byte
BnH 50H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–63: OFF, 64–127: ON)
* This message is used as Realtime Modify (EFFECT) on/o information.
 General Purpose Controller 6 (Controller Number 81)
Status 2nd byte 3rd byte
BnH 51H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL6 (81) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL6 (81) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL6 (81) ,” this message is used as Realtime Modify (EFFECT) control
information.
 General Purpose Controller 7 (Controller Number 82)
Status 2nd byte 3rd byte
BnH 52H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL7 (82) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL7 (82) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL7 (82) ,” this message is used as Realtime Modify (EFFECT) control
information.
 General Purpose Controller 8 (Controller Number 83)
Status 2nd byte 3rd byte
BnH 53H vvH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
vv = control value 00H–7FH (0–127)
* When D-BEAM CC# (MENU --> SYS --> MIDI --> MIDI) setting is “GENERAL8 (83) ,” this
message is used as D-BEAM position information.
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL8 (83) ,” this message is used as Realtime Modify (PITCH) control
information.
* When Realtime Modify Eect CC# (MENU --> SYS --> MIDI --> MIDI) setting is
“GENERAL8 (83) ,” this message is used as Realtime Modify (EFFECT) control
information.
Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
pp = program number: 00H–7FH (prog.1–prog.128)
* The sound will change beginning with the next note on after the Program Change
is received.
* Not received when Program Change Rx (MENU --> SYS --> MIDI --> MIDI) is set to
“OFF.”
Bank Select MSB / LSB Program Number Kit Number
000 / 000 001–128 001–128
001 / 000 001–072 129–200
Pitch Bend Change
Status 2nd byte 3rd byte
EnH llH mmH
n = MIDI channel number: 0H–FH (ch.1–ch.16)
mm, ll = pitch bend value: 00 00H–40 00H–7F 7FH
(-8192–0–+8191)
* When Realtime Modify Pitch CC# (MENU --> SYS --> MIDI --> MIDI) setting is “PITCH
BEND,” this message is used as Realtime Modify (PITCH) control information.