Roland MC-808 - Page 41

41
Effects editing parameters
41: TRIPLE TAP DELAY
Produces three delay sounds; center, left and right.
fig.MFX41
42: QUADRUPLE TAP DELAY
This effect has four delays.
fig.MFX42a
fig.MFX42b
Stereo location of each delay
43: MULTI TAP DELAY
This effect provides four delays. Each of the Delay Time parameters
can be set to a note length based on the selected tempo. You can also
set the panning and level of each delay sound.
fig.MFX43
44: REVERSE DELAY
Adds the reverse of the input sound as a delay.
fig.MFX44
Parameter
Value Description
Delay Left/
Right/Center
0–4000 ms,
note
Adjusts the time until the delay
sound is heard.
Feedback
#1
-98– +98 % Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
HF Damp 200–8000
Hz, BY-
PASS
Adjusts the frequency above which
sound fed back to the effect is fil-
tered out. If you do not want to filter
out any high frequencies, set this
parameter to BYPASS.
Left/Right/
Center Level
0–127
Volume of each delay
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
Parameter
Value Description
Delay 1–4
0–4000 ms,
note
Adjusts the time until the delay
sound is heard.
Level 1–4 0–127 Volume of each delay
Feedback
#1
-98– +98 % Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
HF Damp 200–8000
Hz, BY-
PASS
Adjusts the frequency above which
sound fed back to the effect is fil-
tered out. If you do not want to filter
out any high frequencies, set this
parameter to BYPASS.
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level 0–127 Output level
L in
R in
L out
R out
Left Tap
Right Tap
Triple Tap Delay
2-Band
EQ
2-Band
EQ
Balance W
Balance D
Balance W
Balance D
Feedback
Center Tap
L in
R in
L out
R out
Quadruple Tap Delay
Balance W
Balance D
Balance W
Balance D
Delay 1
Delay 2
Delay 3
Delay 4
Feedback
1
23
4
L
R
Parameter
Value Description
Delay 1–4
0–4000 ms,
note
Adjusts the time until Delays 1–4
are heard.
Pan 1–4 L64–63R Stereo location of Delays 1–4
Level 1–4 0–127 Output level of Delays 1–4
Feedback
#1
-98– +98 % Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
HF Damp 200–8000
Hz, BY-
PASS
Adjusts the frequency above which
sound fed back to the effect is fil-
tered out. If you don’t want to filter
out the high frequencies, set this pa-
rameter to BYPASS.
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Level 0–127 Output level
Parameter
Value Description
Threshold
0–127 Volume level at which the reverse
delay begins
Delay 1–4 0-2000 ms,
note
Adjusts the time until Delays 1–4
are heard.
Feedback 1
#1
-98– +98 % Adjusts the amount of the delay
sound that’s fed back into the effect.
Negative (-) settings invert the phase.
Feedback 4
HF Damp 1 200–8000
Hz, BY-
PASS
Adjusts the frequency above which
sound fed back to the effect is fil-
tered out. If you do not want to filter
out any high frequencies, set this
parameter to BYPASS.
HF Damp 4
Pan 1–3 L64–63R Stereo location of Delays 1–3 sound
Level 1–3 0–127 Output level of Delays 1–3 sound
Balance #2 D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the effect sound (W)
Low Gain -15– +15 dB Gain of the low frequency range
High Gain -15– +15 dB Gain of the high frequency range
Level 0–127 Output level
L in
R in
L out
R out
Multi Tap Delay
Balance W
Balance D
Balance W
Balance D
Delay 1
Delay 3
Delay 4
Delay 2
Feed
back
2-Band
EQ
2-Band
EQ
Feedback 1
L in
R in
Rev. Delay
L out
R out
2-Band
EQ
2-Band
EQ
1
2
D1
Delay
3
D3
D2
D4
Feedback 4
MC-808_Slist_e.book 41 ページ ２００７年９月７日 金曜日 午前１１時１１分