Roland rubix 44 - About the USB Driver

14
About the USB Driver
Windows Operating Requirements
Supported Operating Systems
Microsoft® Windows® 7 / 8 / 8.1 / 10 (64-bit / 32-bit)
* The driver does not work on Windows RT.
Supported Computers
A Windows compatible computer equipped with a USB port
* We recommend a chipset made by Intel.
* Intel Core2 processor 1.6 GHz or faster, RAM 1.0 GB or more
* Performance might be unsatisfactory if this unit is used with a
USB 2.0 interface card.
* This unit cannot be used with a USB 3.0 port that is not
compatible with USB 2.0.
* If the unit does not operate correctly when connected to a USB
3.0 port, you’ll need to connect it to a USB 2.0 port.
* Even if the unit is connected to a USB 3.0 port, the performance
of the unit itself will not change.
* This unit cannot be used in a virtual Windows environment such
as VMware or VirtualBox.
* Mac computers running Windows are not supported.
Limitations and Cautions
5 Depending on the performance and design specications of
the computer you’re using, and on the applications you’re using
and how you’re using them, clicks and pops might occur in the
sound.
5 If you start your computer with a powered-on Rubix already
connected to the computer, the driver might not be loaded
correctly, making it impossible to use the Rubix. If this occurs, try
the following.
5 Reconnect the Rubix to a dierent USB port
5 Power-on the Rubix after the computer has started
5 Disconnect and reconnect the USB cable
5 Sometimes the Rubix might not operate correctly after returning
from a sleep state. If this occurs, try the following.
5 Exit all the applications you’re using, and power-cycle the
Rubix
5 Disconnect and reconnect the USB cable
5 If you disconnect and reconnect the USB cable while using
the Rubix, or power-cycle the Rubix, it might stop operating
correctly. If this occurs, try the following.
5 Exit all the applications you’re using, and power-cycle the
Rubix
5 Disconnect and reconnect the USB cable
5 If a high processing load occurs while using the Rubix, such as
accessing a CD-ROM drive or the network, it might not operate
correctly. If this occurs, try the following.
5 Stop playback/recording, and then resume playback/
recording
5 Exit all the applications you’re using, and power-cycle the
Rubix
5 Disconnect and reconnect the USB cable
5 If you connect or disconnect another USB device (such as a USB
ash drive) while using the Rubix, or turn the power of another
USB device on or o, clicks or pops might occur during playback
or recording.
5 In some cases, performance might be unsatisfactory if the Rubix
is used simultaneously with a USB-connected hard disk. Don’t
use a USB-connected hard disk as the save-destination for
playback or recording.
Mac OS Operating Requirements
Supported Operating Systems
OS X v10.12 / v10.11 / v10.10
* Check the operating requirements of your audio/MIDI
application as well as the operating requirements for your
operating system.
Supported Computers
Apple Mac series computer equipped with a USB port
* Even if the unit is connected to a USB 3.0 port, the performance
of the unit itself will not change.
* Mac computers running Windows are not supported.
Limitations and Cautions
5 Connect the Rubix to your computer with a USB cable before
starting your sequencer software, etc.
5 Don’t power-o the Rubix or disconnect the USB cable during
playback/recording. Doing so might cause the software or
operating system to shut down abnormally.
5 Exit your sequencer software etc. before you power-o the
Rubix or disconnect the USB cable.
5 Before updating the operating system software, disconnect the
USB cable from the Rubix.
5 If the Rubix does not operate correctly after returning from sleep
or after restarting the operating system, try the following.
5 Exit all the applications you’re using, and power-cycle the
Rubix
5 Disconnect and reconnect the USB cable
iPad Operating Requirements
Supported Operating Systems
iOS 9.0 or later
Limitations and Cautions
5 Connect the Rubix to your iPad with a USB cable before starting
your sequencer software, etc.
5 Don’t power-o the Rubix or disconnect the USB cable during
playback/recording. Doing so might cause the software or
operating system to shut down abnormally.
5 Exit your sequencer software etc. before you power-o the
Rubix or disconnect the USB cable.
5 Before updating the iOS software, disconnect the USB cable
from the Rubix.
5 If the Rubix does not operate correctly after restarting iOS, try
the following.
5 Exit all the applications you’re using, and power-cycle the
Rubix
5 Disconnect and reconnect the USB cable