Roland TD-7 - How to read a MIDI Implementation Chart

2.2 Receive Messages to Control the System
IChannel Voice message
OP:-ogram Change
Status Second
Col-I Milt
if the “Prg Chg Rx" of the Mil)! parameter is set at ON, the TD-‘i’ receives
on the channel set by "Ctrl Ch" of the MIDI parameter.
This message is not recorded in the Phrase Sequencer.
-System Real Time Messages
OTimin9 Clock
Status
FBH
Recognize oniy sync mode when sot at MIDI.
‘Active Sensing
Status
FEH
Whenever the Tl} 1' receives this message. it monitors the interval of the incoming
data. ll the subsequent message has not arrived within Sdtlms alter the previous
data. it processes all sections as though it has received a Reset All Controllers.
and mules the sounding voices. then stops monitoring receiving interval.
Isvstem Exclusive Message
Status
F0!-I :System Exclusive
F'?li :{-IOX (End of Exclusive}
with the TD-7. the System Exclusive Message can be used to transmit and receive
parameters of sequence and setup data.
For details refer to "Roland Exclusive Messages" and paragraph "3. Exclusive
Communications."
Ignore System Exclusive message if oaramctcr Sys Exc Rx =OFF of Mil)!
Parameter.
System Exclusive messages are not recorded in the Phrase Sequencer.
l3-E><<='v$i\£.s°° mm“ "isa*i°"$l
IGenera| -
'i‘D~T can do one» way communications to send and receive parameters for
sequence and setup.
Model ll) inciudod in the exclusive message should be 5531!. The device ID code
should be MIDI parameter Device ID of System. Note that the actual value that
set in the device ID field is smaller by one than the value set at parameter
Device ii) oi System.
IOne Way Communications
Request data RQ1 HH
Bvte Description ._____ s _
FOH Exclusive status
411-! Manufacturer ID (Roland)
DEV Device ID (OOH Hill)
58H Model to (Ti)-7)“
illt Command ll) (RQH
aaH Address M58
aall Address
aall Address
aall Address LSB
ssH size MSB
ssH size
sslt size
55!"! size LS8
sum Check sum
F7!-i BOX (End oi Exciusivel
Data set l)Tl |2i-l
liytc . _.l1psc riptimi if
I-‘fill I-Ixclusive status
rill-I klanufacturer if) {Roland}
Di-It’ Device ll) {OOH ll-‘ill
58!-l .\.-lode! ll) {TD-‘Ii
l2i-l Command ..lD i¥)'l‘ll
aall Address MSB
aall Address
aail Address
aali Address L513
ddll data
sum Check sum
I-"ill {BOX (I.-Intl of l§.\tciusi\-‘cl
ITransmission
The TD-T transmits Eltciusivo messages only when .lvllDl Bulk dump is iierfornzt.-ti
by panel otleration in the menu of System iunctions.
-Receive
TD-7 is stopped and Built tiumtJ is not performed.
" ‘i; _II__ _ i_ _ JL____._ ___._ ____:___ ___ __ Jamal ' haul" *
[4~Pa!ame*e! addrsssdagl
Addresses are shown in ever)-' 7 - bit hexadecimal.
Add toss -llS!Ii LS l5
Binary i Gotta aaaa . tlhhti tzhbb - {lectr cccc t llddd ddtltl
- lthlt heat. " AA tilt CC = llli
...... .. ....._.....-._.._.._.._.._--_ . . .
-Parameter base addresses
Start
Address Descrlutinn
£10 tit} till 00 Patch parameters M-I
- ¢
I .
0! B0 till G0 instrument parameters H~L‘
U2 fill {Ill till glohai performance parameters #4"-'3
03 tltl 80 tit} system set up til--l
0 0
fit Dtl B0 00 chain setup M-5
05 09 G0 00 sequence data Hi-ti
Table -1 s I Patch parameters
pp: Patch i\2o.(0 31>
nn : Note l\Zo.(35 -~ 93)
tt :TRlG Noll 2 Tl 2:Rl ~ l’? : T9 l8:R9)
Offset
Add ress Desert pt ion
pp U6 U0 PROGRAM CHANGE No.
00 Bl PROGRAM CHANGE So. i{l:UFFl
OB B2 fiame A5CIl(leiti I2?
tltl tilt " Nettie ASCH 12?
on at vast ASCII - 121
no 05 some .=\St".lt I2?
{iii lili {tame ASCII I2?
till GT Name A5Cii(rlght) I2?
l‘.-;&Jr..-.:b3I-22.-3:31;: {wt-'I--fir-crab-3r.:
-. ..,
3 --.1
00 08 PFMI SUUNU (1-5!?) E996? Zbits ~ 3
00 B9 ?FHi SOEND ti 512) Loser Tbits 12?
D9 BA PFH2 SOEND (1~5l2l U098? Zbits 3
00 BB PFM2 SOHND (I 512) Lower Ybits I2?
00 BC PFH3 SOUND (1-532) U090? Zbits 3
OD GD FFM3 SUUNU (i-512} Lower Tbils 12? ' l:IZCDl=3ZZ
1:-it