Fejlfindings skema
PROBLEM
SKYLDES
HJA:LP
SIDE_
KnlHker
I.
Spolen er ikke korrckt isat.
I.
Se side 23
undertrlden
2. Undertr6dcn or for stram.
2. Se side
21
3. Spolcn er
tddet
forkcrt. 3. Se side 23
4. Der
or
sleV
i .polekap.lcn
og
4. Se
.ide
73
tdd.p"",ding.fjedcren.
Sprinltr
,lInl
I. NlIcn er ikke korrekl isat.
I.
Se
.ide
13
over 2. NlIcn or bcskadiget. 2. Se
.ide
13
3. Forkert type
nll
blivor brugt. 3. Se
.ide
77
4.
Tridningcn
.f
overbidcn
er
4. Se side
IS
forkert.
S.
Forkert trykfod blivor brugl.
S.
Se
.ide
9
Ure&eI
......
I. Forkert
nlle
.Ir.
i fomold til I. Se side 77
•
lIna!l.dferinl
or
stoffet .
stof
2.
Ovel"llidsspamdingen er for 2. Se
side31
195.
3. Forkert underbidssp",nding. 3. Se
.ide
21
Stoffel
rynker
I.
Ovcr-
ella
undertJids-
I.Seside21+31
sp",ndingcn or for.tram.
2.
Stingcne or for lange til .toffet. 2. Skift
.ting-
3. Triden er for tyk.
I",ngde
4. Forkert
tddning
af
over
og
3. Se
.ide
77
underbidcn.
4. Se
.ide
15+23
Triode.e.lir
I. Overbidcn er ikke
tddet
I.
Se
.ide
IS
Duder
korrckt.
2.
Spolcn er ikke
tddet
kom:kt. 2.
Se.ide
23
3.
NIUtdd
fomold or ikke 3. Se
.ide
77
kom:kt.
KnlHker
1.
NAien
er
ik..ke
isst kom:kt. I. Se
.ide
13
o.ertriode.
2. Nlien
er
bcskadigcl 2. Se
.ide
13
3. NlIeholde",kruen er Iss.
3. Se
.ide
13
4. Overbidssp",ndingcn er for 4. Se side
31
• tram.
S.
NlIen or for fin til.toffet.
S.
Se side 77
6. Maskinen
er
trAdet
forlc.ert.
6. Se
.ide
I
S+
23
7. Der er blevet .tillet
pi
map-
7. Se
.ide
13
peme.
mens
nAien
har
VICret
nede i stoffel.
Ma.kinen
lar.er
I. Symaskinen mangler olie. I.
Srnsr
maskinen.
oa
urer
ujavDI
2. TrAdtro:vlerog olie res\cr har
2.
Ren.
griberlejet.
samlet sig i griber eller
pi
nile
3. Rens maskinen
slangen.
og
.msr
med
fin
3. Olie
af
dirlig kvalitet or brugt. symaskinc
olie
4. NlIen er bcskadiget. 4. Skill nilen
S.
Stingl"'ngden
er
indstillet
S.
Skill sting-
forkcrt til
de
sting
der
bruges. Ia:ngde
BEMJERK:
Gem
original emballage.
For
silcker forsendelse i forbindelse med
eventuel service efters
y
n.
75
Trouble shooting
PROBLEM
CAUSE
REMEDY
Bobbin
tbread
I.
Bobbin not inserted correctly.
I.
Sec page 24
brnkl
2. Bobbin threod to tight. 2.
Seepage
24
3. Bobbin
incorrectly wound 3.
Seepage
24
4. Dust
in
bub bin case. 4. See page 73
SlItcb
..
are
left
I.
Needle not properly fitted
on
I. See page
13
oul
needle bar. 2. See page
13
2. Needle bent. blunt
or
worn. 3. See page 73
3. Wrong needle
Iype
i.
being 4. See page
16
used.
S.
See page 10
4. Threoding
of
needle threod is
not correct.
5.
Wrong presser foot.
Irregular
stilcb
..
I. Needle size not suited to I. Use top quality
fabric. threods.
2. Check threod
2. Needle threod tension too
tension.
loose. 3. Check bobbin
3. Wrong bobbin
threod tension. thread tension.
SbrinK
or
I. Needl.,.
or
bobbin tension too
I. Check needle!
puckorinlortbo
tight.
bobbin
threod
lea.
2. Stitches are too long for the tension regu-
fabric. latian.
3.
Threod too thick.
2.
4. Wrong
threoding
of
needle 3. See "Size
of
and bobbin thread.
needle and
threod"
4. Check
threoding.
Thread
forms
I.
Needle threod not threaded
I. Check
loop.
correctly. threoding.
2. Bobbin not threaded
correctly. 2. Check threadin
3. Needle!thread do not
correspond .
3.
See "Size
of
needle and
threod".
Needlolbread
I. Needle not inserted correctly. I. Insert needle
breakJ
2. Needle damaged. correctly.
3. Needle screw loose.
2. Replace.
4. Needle thread tention too 3. Fasten screw.
tight. 4. Check tension.
5.
Needle too thin for
the
fabric.
5.
See "size
of
6. Wrong threoding.
needle and
7. Buttons have been adjusted. thread"
while the needle have been in
6. Check
the fabric. threading.
7.
Check buttons.
Machine doe!
not
I. Machine needs oiling.
1.
Oil
the
machine
run
freely
and
2. Dust and thread
in
shuttle. 2. Clean the
makes I
noile
3. Wrong oil has been used. shuttle.
4. Needle has been damaged.
3. Clean the
5.
Stitch length
is
wrong
machine
and
oil
compared to the selected with fine sewin
stitch. machine oil.
NOTE: Save original container.
For safe transport for service check
if
necessary.
To Next Page
Loading...
