EasyManuals Logo

Ruckus Wireless ZoneFlex 7982 Quick Start Guide

Ruckus Wireless ZoneFlex 7982
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Copyright © 2013 Ruckus Wireless, Inc. Page 1 of 4
Published June 2013, Part Number 800-70362-001 Rev F
ZoneFlex 7982
Dual Band 802.11n
Multimedia Wi-Fi Access Point
Quick Setup Guide
This Quick Setup Guide provides step-by-step instructions
on how to set up your Ruckus Wireless ZoneFlex Access
Point. After completing the steps described in this Guide,
you will be able to place the Access Point (AP) at your site
and provide wireless network access to users.
THIS GUIDE IN OTHER LANGUAGES
请从以下网站获得该指南的简体中文版
https://support.ruckuswireless.com
.
Vous trouverez la version française de ce guide à l'adresse
suivante https://support.ruckuswireless.com
.
⽇本語版 https://support.ruckuswireless.com
でご
가이드의 한국어 버전은 사이트
(https://support.ruckuswireless.com
) 에서 확인하시기 바랍니다 .
Veja a versão em português (Brasil) deste guia em
https://support.ruckuswireless.com.
Puede ver la versión en español (América Latina) de esta guía en
https://support.ruckuswireless.com
BEFORE YOU BEGIN
Before deploying Ruckus Wireless products, please check for
the latest software and the release documentation.
User Guides and Release Notes are available at
http://support.ruckuswireless.com/documents.
Software Upgrades are available at
http://support.ruckuswireless.com/software.
Open Source information is available at
http://opensource.ruckuswireless.com.
Software License and Limited Warranty are available at
http://support.ruckuswireless.com/warranty.
PACKAGE CONTENTS
ZoneFlex 7982 Access Point
Mounting screws and anchors (2)
T-Bar clips and alignment spacer
Regulatory flyer
•This Quick Setup Guide
SETUP REQUIREMENTS
A computer running Windows 7 (procedures for other OS’s
are similar)
One or more of the following:
A modem (DSL or cable), broadband router, or other
device provided by your Internet Service Provider
that brings Internet access to your site.
A network switch or a DSL/Internet gateway device.
Two Cat 5e Ethernet cables
An AC power adapter (sold separately), or
An 802.3af or 802.3at -compliant Power over Ethernet (PoE)
switch or PoE injector
STEP 1: CONNECT THE AP TO YOUR COMPUTER
1 After removing your Ruckus Wireless AP from its pack-
age, place it next to your computer.
2 Using an Ethernet cable, connect your computer’s net-
work port to one of the two ports on the AP.
3 Using an AC adapter (sold separately), connect the AP to
a convenient (and protected) power source.
Alternatively, connect the 10/100/1000 POE port to a
PoE injector or switch for both power and network
connectivity.
4 Verify that the Power LED on the external enclosure is a
steady green.
STEP 2: PREPARE YOUR COMPUTER FOR AP
S
ETUP
1 On your Windows 7 computer, configure your network
adapter from the Local Area Connection settings as fol-
lows:
Start > Control Panel > Network and Sharing Cen-
ter > Change Adapter Settings
2 Edit the TCP/IPv4 address settings as follows:
Local Area Connection > Properties > Internet
Protocol Version 4 (TCP/IPv4) > Properties
The TCP/IPv4 Properties dialog box appears.
3 Select Use the following IP address (if it is not already
selected) and then make the following entries:
IP address: 192.168.0.22 (or any address in the
192.168.0.x network)
Subnet mask: 255.255.255.0
Default gateway: 192.168.0.1
Leave the DNS server fields empty.
4 Click OK to save your changes.
Your changes are put into effect immediately.
NOTE: The ZoneFlex 7982 requires a minimum of Zone-
Flex firmware version 9.4 and above to operate.
IMPORTANT!
If the AP is deployed with a ZoneDirector, follow the
ZoneDirector Quick Setup Guide and connect the AP to
your local network.
NOTE:
The following procedures assume Windows 7 as the oper-
ating system. Procedures for other OS’s are similar.
IMPORTANT!
Write down all of the currently active settings so you can
restore your computer to its current configuration later
(when this process is complete).
PoE In
DC input

Other manuals for Ruckus Wireless ZoneFlex 7982

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Ruckus Wireless ZoneFlex 7982 and is the answer not in the manual?

Ruckus Wireless ZoneFlex 7982 Specifications

General IconGeneral
2.4 GHzYes
Modulation-
Frequency band2.4 - 5 GHz
Number of users500 user(s)
Channels quantity11 channels
Networking standardsIEEE 802.11a, IEEE 802.11b, IEEE 802.11e, IEEE 802.11g, IEEE 802.11i, IEEE 802.11n, IEEE 802.1Q, IEEE 802.1x, IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3at, IEEE 802.3u
Wi-Fi data rate (max)450 Mbit/s
Ethernet LAN data rates10, 100, 1000 Mbit/s
Maximum data transfer rate1000 Mbit/s
Supported network protocolsIPv4, IPv6, L2TP, PPPoE, HTTP/S, Telnet/SSH, FTP, TFTP
Ethernet LAN (RJ-45) ports2
Security algorithms802.1x RADIUS, WEP, WPA-PSK, WPA-TKIP, WPA2-AES
Antenna featuresIntegrated antenna
Antenna gain level (max)3 dBi
Input current1.5 A
AC input voltage12 V
Power consumption (typical)7 W
InternalNo
Product colorWhite
Cable lock slot typeKensington
Operating temperature (T-T)0 - 50 °C
Operating relative humidity (H-H)0 - 95 %
Weight and Dimensions IconWeight and Dimensions
Width203 mm
Height50 mm
Weight1000 g

Related product manuals