English(original instructions)
EN
FR DE ES IT PT NL SV DA NO FI HU CS RU RO PL SL HR ET LT LV SK BG
Q #LEANTHEAIRFILTER2EFERTO#LEANINGTHE!IR&ILTERIN
THEMaintenanceSECTIONOFTHISMANUAL
Q !LLOWTHE ENGINETO WARM UP PRIOR TOADJUSTMENT OF
ENGINEIDLESPEED
7!2.).'
7EATHER CONDITIONS AND ALTITUDE MAY AFFECT
CARBURETION$ONOTALLOWBYSTANDERSCLOSETOTHE
CHAINSAWWHILEADJUSTINGTHECARBURETTOR
)DLE3PEED !DJUSTMENT
controls how much the throttle valve stays open when the
Q 4URNIDLESPEEDSCREW±4²CLOCKWISETOINCREASEIDLE
SPEED
Q 4URN IDLE SPEED SCREW ±4² COUNTER CLOCKWISETO
DECREASEIDLESPEED
7!2.).'
4(%3!7 #(!).3(/5,$ .%6%2452.!4
)$,% 3ERIOUS PERSONALINJURY MAYRESULT FROM
THESAWCHAINTURNINGATIDLE
#,%!.).'4(%%.').%
See Figures 58, 62-64.
Clean the engine fins and flywheel fins with a brush
periodically. Dangerous overheating of the engine may
occur due to impurities on the engine.
7!2.).'
.EVERRUNTHESAWWITHOUTALLTHEPARTSINCLUDING
THECLUTCHCOVERANDSTARTERHOUSINGSECURELYIN
PLACE
Because parts can fracture and pose a danger of thrown
objects, leave repairs of the flywheel and clutch to factory
trained authorised service centre personnel.
Q 2EMOVETHE SCREWSANDENGINE COVERASDESCRIBED
PREVIOUSLY
Q #LEANTHEENGINEFINS
Q ,IFTTHECHAINBRAKEOVERTHEPOST
Q ,AYTHECHAINSAWONITSSIDE WITH THEBARAND CHAIN
ONTHEGROUND
Q 2EMOVETHECHAINLUBRICANTANDFUELCAPS
Q 2EMOVETHETHREESCREWSTHATHOLDTHESTARTERHOUSING
INPLACE
Q ,IFTOFFTHESTARTERCOVERANDSETASIDE
Q 2EPLACE CHAIN LUBRICANT ANDFUEL CAPS TO PREVENT
CONTAMINATIONDURINGCLEANING
Q #LEANTHEFLYWHEELFINS
Q 2EPLACETHE STARTER HOUSING 2EINSTALLSCREWSAND
SECURE
Q 2EPLACETHECHAINLUBRICANTANDFUELCAPS
Q 2EPLACE THE ENGINE COVER 2EINSTALL SCREWS AND
SECURE
Q 2EPLACETHECHAINBRAKEONTHEPOST
./4%#HECKTO ENSURE THATTHE AIRFILTER ISIN THE
PROPERPOSITIONBEFOREREINSTALLINGTHEENGINECOVER
./4%If you notice a power loss with the petrol powered
removed to restore performance. We highly recommend
that only qualified service technicians perform this
service.
#(%#+).'4(%&5%,&),4%2
See Figure 65.
Check the fuel filter periodically. Replace it if
contaminated or damaged.
2%0,!#).'4(%30!2+0,5'
See Figure 66.
every 50 hours or more frequently, if necessary.
Q 2EMOVE THE SPARK PLUG LEAD BYCAREFULLYROTATING
BACKANDFORTHWHILSTGENTLYPULLINGUPWARDS
Q ,OOSENTHESPARKPLUGBYTURNINGITCOUNTERCLOCKWISE
WITHAWRENCH
Q 2EMOVETHESPARKPLUG
Hand thread the new spark plug, turning it clockwise.
.OTE Be careful not to cross-thread the spark plug.
Cross-threading will seriously damage the engine.
Q 2EATTACHTHESPARKPLUGLEADBYPRESSINGFIRMLYONTO
TOPOFSPARKPLUG
).30%#4).'#,%!.).'4(% 30!2+ !22%34/2
3#2%%.
See Figure 67.
A faulty spark arrestor screen can create a fire hazard.
should be inspected weekly and cleaned as required.
Always keep the Silencer and spark arrestor on the saw
in good condition.
7!2.).'
3ILENCERSURFACESAREVERY HOTDURINGAND AFTER
OPERATIONOF THE CHAINSAW4O AVOID SERIOUS
PERSONALINJURYKEEPALL BODY PARTS AWAYFROM
THE3ILENCER
Q !LLOWTHE3ILENCERTOCOOL
Q 2EMOVETHEDEFLECTORRETAININGSCREW
Q 2EMOVE THEDEFLECTOR TOACCESS THESPARKARRESTOR
SCREEN
Q )F DIRTYCLEAN THESPARKARRESTOR SCREENWITH ASMALL
WIREBRUSH2EPLACE THESCREEN IF IT IS CRACKED OR
OTHERWISEDETERIORATED4OOBTAINAREPLACEMENTSPARK
ARRESTORCONTACTYOUR2YOBISERVICECENTRE
To Next Page
Loading...
